manualshive.com logo in svg

AGCO LELY ATTIS PT 130, Operator'S Manual

Share
Download
AGCO LELY ATTIS PT 130 Operator'S Manual Download Page 57

3.6   Disconnect the machine from the tractor

3.6.1  Park the machine

WARNING: Risk of sudden movement.

Always stop the engine and remove the ignition key when you exit the tractor.

Procedure

1.

Park the machine on solid ground before you disconnect it from the tractor.

2.

Collect the wheel chocks from the storage

area of the machine and put them behind the

transport wheels.

GUID-61252C8C-99E0-4AE3-BD4C-AC6CD3D47149-high.jpg [High]

Fig. 32  

3.

Move the parking jack to the correct position

and lock it.

4.

Turn the handle of the parking jack to release

the tension on the pull eye.

GUID-BE884F5C-1B59-4285-81DD-F9F496E9C7CD-high.jpg [High]

Fig. 33  

3.6.2  Remove the pressure from the hydraulic system.

WARNING: Risk of sudden movement.

Always stop the engine and remove the ignition key when you exit the tractor.

Procedure

1.

Release the pressure in the tractor hydraulic system.

2.

Disconnect the two hydraulic hoses from the tractor hydraulic system.

3.

Attach the dust caps to the two hydraulic hoses.

[V]

GUID-5119662E-306D-4A97-93F6-545BEACF6847 [V1]

GUID-4069AC69-30A4-4DFD-B22B-181B6E16F7E8 [V1]

3. Operation

Bale Wrapper 

57

4820.LE.EN01

Summary of Contents for LELY ATTIS PT 130



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands