manualshive.com logo in svg

AGCO LELY ATTIS PT 130, Operator'S Manual

Share
Download
AGCO LELY ATTIS PT 130 Operator'S Manual Download Page 61

4.1   Prepare the machine to do maintenance

WARNING: Risk of contact with dangerous materials.

Put on the correct Personal Protective Equipment (PPE) when you use lubricants and oils.
Lubricants and oils are dangerous to health and the environment.

WARNING: Risk of personal injury.

Release the hydraulic pressure before you do maintenance on the machine.

Procedure

1.

Move the machine on to flat and level ground.

2.

Put the wrapping table in the maintenance

position.

3.

Set the E-link controller to OFF.

4.

Set the tractor ignition to OFF.

GUID-1F3EAEA0-182A-417F-B9F8-8B193F938A5E-high.jpg [High]

Fig. 1  

5.

Close the valve on the hydraulic cylinder to

keep the wrapping table in the maintenance

position.

GUID-70BCE0D4-AE03-41E1-8765-A8D2F657F32A-high.jpg [High]

Fig. 2  

A

Valve OPEN 

B

Valve CLOSED 

GUID-0CF02619-3A2B-4578-8B2D-BEC6A3C577EF [V1]

4. Maintenance and lubrication

Bale Wrapper 

61

4820.LE.EN01

Summary of Contents for LELY ATTIS PT 130



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands