manualshive.com logo in svg

AGCO LELY ATTIS PT 130, Operator'S Manual

Share
Download
AGCO LELY ATTIS PT 130 Operator'S Manual Download Page 20

1.4.7  Wheel chocks

When the machine is not in use or not connected

to the tractor, the wheel chocks must be in

position to stop the machine from sudden

movement.

GUID-61252C8C-99E0-4AE3-BD4C-AC6CD3D47149-high.jpg [High]

Fig. 8  

1.4.8  Transport lock for bale end tipper

The bale tipper has to be in its up position for

transport. When you transport the machine, install

the bracket with pins and clips in there slots. This

lock device stops the bale end tipper from sudden

movement and decreases the length of the

machine for transport on the road.

GUID-D643846F-12CB-4FE6-AAD6-86C1F3E29A81-high.jpg [High]

Fig. 9  

1.4.9  Bale end tipper

The bale end-tipper sets the bale on its end during

the bale unload. This makes sure that the bale

cannot move on a slope and decreases the

damage to the wrapped bale because the ends

have more film applied.

NOTE: 

Stop the tractor when you release the bale

on to the bale end tipper.

GUID-32CEA606-B789-4D82-A66C-50E3D39FADD0-high.jpg [High]

Fig. 10  

GUID-FA7F3371-DCA0-4974-95AC-7A90CEB62F94 [V1]

GUID-4BD18C34-A03B-4F76-9693-4A640714BB15 [V1]

GUID-55E70BD0-3C93-4243-9F28-78781EDE7AC8 [V1]

1. Safety

20

Bale Wrapper

4820.LE.EN01

Summary of Contents for LELY ATTIS PT 130



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands