ADTRAN TOTAL ACCESS 600R, System Manual

Page: 87 / 196

Total Access 600R System Manual Section 4 User Interface Guide
61200600L1-1A © 2002 ADTRAN, Inc. 87
A
DDRESS
M
ODE
This option determines how the WAN interface receives its IP address.
U
SER
S
PECIFIED
is the normal
mode of operation.
• The choices are
U
SER
S
PECIFIED
(default) and
IPCP A
SSIGNED
if the
L2 P
ROTOCOL
is set to
PPP
.
• The choices are
U
SER
S
PECIFIED
(default),
IARP
, and
DHCP C
LIENT
if the
L2 P
ROTOCOL
is set
to
F
RAME
R
ELAY
.
IARP
can be used to learn the far-end IP address.
• If using the Auto-config option and the
L2 P
ROTOCOL
is
PPP
, the default is
IPCP A
SSIGNED
.
This means the unit will learn its IP address from a router on the WAN during IPCP
negotiation. It is the same mechanism used by the auto-detection algorithm.
• If using the Auto-config option and the
L2 P
ROTOCOL
is
F
RAME
R
ELAY
, the default is
DHCP
C
LIENT
. This means a DHCP Server from the service provider will issue this unit an IP address
using DHCP.
• If the Auto-config option is not used, the
U
SER
S
PECIFIED
option for both
PPP
and
F
RAME
R
ELAY
allows the IP addresses to be statically programed into the unit.
L
OCAL
IP A
DDRESS
(This option is only applicable in
U
SER
S
PECIFIED
address mode.) For
PPP
, this IP address is the local
WAN IP address and can be statically assigned if using numbered interfaces. For
F
RAME
R
ELAY
, this
is the numbered IP associated with this DLCI interface. This address is used by the unit to respond to
Inverse ARP requests. If this IP address is left as
0.0.0.0
, the link is treated as unnumbered and the
unit responds to the Inverse ARP with its Ethernet IP address. Default is
0.0.0.0.
IP N
ETMASK
(This option is not available for
F
RAME
R
ELAY
DHCP C
LIENT
A
DDRESS
M
ODE
.) For Frame Relay, the
IP netmask which is applied to the
F
AR
-E
ND
IP A
DDRESS
and
L
OCAL
IP A
DDRESS
is specified here.
Default is
0.0.0.0.
For the PPP protocol, this network mask is applied to the
F
AR
-E
ND
IP
ADDRESS
for
determining the PPP peer’s network. If left as
0.0.0.0
, a standard network mask is used. Default is
0.0.0.0.
F
AR
-E
ND
IP A
DDRESS
(This option is not available for
F
RAME
R
ELAY
DHCP C
LIENT
A
DDRESS
M
ODE
, F
RAME
R
ELAY
IARP
A
DDRESS
M
ODE
, or
PPP IPCP A
SSIGNED
A
DDRESS
M
ODE
.)
For Frame Relay, this is the IP address of
the device on the other end of the virtual circuit. When this DLCI becomes active, the unit will add a
route in the IP routing table. Default is
0.0.0.0.
For the PPP protocol, the PPP peer’s IP address or
network can be set here, if known. Leaving this at
0.0.0.0
means that the unit will determine the PPP
peer’s IP and network (if unnumbered) using the PPP IPCP. Default is
0.0.0.0.