manualshive.com logo in svg

Adtec RD-71, User Manual

Share
Download
Adtec RD-71 User Manual Download Page 70

 

allows users to filter or cherry pick programs destined for the output from an MPTS input. 
Up to 5 services can be mapped to the ASI Filtered output.

 

 
ASI TS Source

​

 - 

​

ASI TS Source configures the transport stream input to ASI output routing 

of the IRD.

 

 
ASI Output TMR

​

 - 

​

ASI Output TMR determines the ASI egress rate. When set to AUTO, the 

default, the output rate will be the sum of all PIDs configured for the  minimal NULL 
stuffing. When set to NATIVE, the output TMR is set to match the INPUT source TMR. 
MANUAL is a user defined rate.

 

 
Manual TMR

​

 - When ASI Output TMR is set to MANUAL, this field may be configured for a 

value in Mb/s. 
 
IP Tx

​

 configures IP Destinations and Service Filtering for the IP Outputs.  A summary table 

of active configuration can be seen when visiting the IP Tx tab.  Click edit next to the 
desired destination to configure parameters.  Read more about protocols in the 

​

IP section

​

. 

 

 

 
 

 

70

 

Summary of Contents for RD-71























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands