manualshive.com logo in svg

Adtec RD-71, User Manual

Share
Download
Adtec RD-71 User Manual Download Page 103

 

Once the unit is back up, select the correct Connector for the IP input, the default is IP2. 

 

As ZIXI-Link is a point to point transport input 0.0.0.0 into the Address field. Then input the correct 
port that the Zixi Feeder is set to. Default is 2088. Then click Apply. 

 

Via the Inpu -> RD Services tab,  select the ‘Select first found’ radio button next to IP.  If all settings are 
correct then the Zixi stream should appear and start decoding. 

 

Setting up Zixi Rx

 

To use Zixi-Rx, the feature key must be enabled.  This may be verified on the Upgrade -> Features tab. 

 

If the key is not enabled please contact your sales representative, 

​

[email protected]

​

. 

Select ZIXI Rx under IP Rx Mode. 

 

The Web interface will prompt for a reboot confirmation, click Apply. 

 

Once the unit is back up select the correct Connector for the IP input, default is IP2. 

 

 

103

 

Summary of Contents for RD-71























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands