Adtec RD-71 User Manual Download Page 25

Page: 25 / 118

Video Menu

Item

Function

Options

Output Menu

Fault Mode

Display or Modify the current SDI

video fault setting. This setting

sets the video resolution when in

video fault.

This setting will be applied on

startup when no video is

present. If video becomes

present, the setting will be

overridden by the current video

setting.

480i59.94

576i50

720p59.94

720p50

1080i59.94

1080i50

1080p59.94

1080p50

Video Loss

When video is not detected on

the configured input, this setting

will define the output.

OFF:No video output on fault

BLANK:Only blanking on fault

BLANKTONES: Blanking and tones

on fault

BLANKOVERLAY: Blanking and

overlay on fault

BLANKTONESOVERLAY

Blanking, tones and overlay on fault

When a type with BLANK is

selected, the current bars/matte

setting will be applied.

When a type with TONES is

selected, the current tones setting

will be applied.

When a type with OVERLAY is

selected, the current device name

will be used.

3G Mapping

Level SDI

SDI 3G Level controls the

mapping of the 3G-SDI signal

when decoding 1080P50,

1080P59.94 and 1080P60

streams. The 3G-SDI signal can

be mapped to Level A or Level B

Dual Link. The mapping is

individually configurable for each

set of outputs (SDI and SDIALT).

A
B

Summary of Contents for RD-71























































































































Search results

Summary of Contents for RD-71

Reviews:

Brands by name

Popular brands

Adtec RD-71, User Manual

Search results

Summary of Contents for RD-71

Reviews:

Brands by name

Popular brands