manualshive.com logo in svg

Adtec RD-71, User Manual

Share
Download
Adtec RD-71 User Manual Download Page 55

 

dropped packets.  In a perfect application, the recovered packets plus the FEC recovered 
packets should be equal to the amount of dropped packets. IE, For every dropped packet, 
the packet was recovered. 
 
Non-Recovered Packets

​

 shows how many packets have been lost. If a packet is lost then 

it is possible that a service artifact or disruption could be seen.  The severity of the artifact 
depends on the type of packet lost (Table, Video, Audio, NULL, etc.). 
 
FEC Recovered

​

 shows how many dropped FEC packets have been successfully recovered. 

 
ARQ Recovered

​

 shows how many dropped packets have been successfully recovered by 

ARQ. 
 
FEC Packets

​

 shows how many FEC packets have been received. 

 
ARQ Packets

​

 show how many ARQ packets have been received. 

 
FEC Bitrate

​

 shows the data rate of the FEC overhead. 

 
Duplicates

​

 shows the number of duplicate packets received via ARQ. 

 
FEC Packet Rate

​

 shows the number of FEC packets received per second. 

 
Requests 

​

shows the number of requests for retransmission of dropped packets made with 

ARQ 

 

55

 

Summary of Contents for RD-71























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands