manualshive.com logo in svg

Adtec RD-71, User Manual

Share
Download
Adtec RD-71 User Manual Download Page 38

 

access to the Stealth IP Address. 

Time Menu 

 

 

Time 

Defines system time 

user-defined using the numeric 
keypad 

Timezone 

Defines the time zone the unit 
operates in 

 

NTP Menu 

 

 

NTP Status 

Network Time Protocol SYNC 
status 

Read-only 

NTP IP Address 

IP address designated for 
Network Time Protocol 

user-defined using the numeric 
keypad 
 
Default is 0.0.0.0. Using all 0’s 
effectively turns this function 
off. 

Alarm Menu 

 

 

Event Record 

Log of events outside of regular 
operating parameters 

scroll up and down to view log 
items 

SNMP Menu 

 

 

SNMP 

Controls the status (ON/OFF) of 
the Simple Network Management 
Protocol (SNMP) feature. We 
support SNMPv2c. 

OFF 
ON 

Read-only 
community 

The Simple Network Management 
Protocol (SNMP) Read-Only 
Password. Default Value: "adtec" 

user-defined using the numeric 
keypad 
default: adtec 

Read-write 

community 

The Simple Network Management 

Protocol (SNMP) Read-Write 

Password. Default Value: "none" 

user-defined using the numeric 

keypad 

default: none 

Trap Community 

The Simple Network Management 

Protocol (SNMP) trap community. 

Default Value: "public" 

user-defined using the numeric 

keypad 

Trap Sink 

The Simple Network Management 

Protocol (SNMP) trap sink, 

destination for sending SNMP 

traps. Default Value: "127.0.0.1" 

/ localhost. 

user-defined using the numeric 

keypad 

 

38

 

Summary of Contents for RD-71























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands