manualshive.com logo in svg

Adtec RD-71, User Manual

Share
Download
Adtec RD-71 User Manual Download Page 60

 

Genlock Status

​

 shows the state of the Genlock system.   

 
Video Output

​

 is used for configuring the video outputs. 

 

 

 
3G-SDI Mapping Level

​

 - SDI 3G Level controls the mapping of the 3G-SDI signal when 

decoding 1080P50, 1080P59.94 and 1080P60 streams. The 3G-SDI signal can be mapped to 
Level A or Level B Dual Link. The mapping is individually configurable for each set of outputs 
(SDI and SDIALT). If 3G-SDI output does not appear on the downstream device, the device 
may not support the currently configured mapping mode. Use SDI3GLEVEL to change the 
mapping mode. 
 
Down Scaling

​

 - The SDI out scale configuration controls the format of the SDI output 

banks, SDI and SDIALT. Each bank has a unique configuration allowing simultaneous HD 
and SD output. When set to OFF, the native resolution is output. When set to SD, the output 

 

60

 

Summary of Contents for RD-71























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands