manualshive.com logo in svg

Adtec RD-71, User Manual

Share
Download
Adtec RD-71 User Manual Download Page 26

 

If 3G-SDI output does not 

appear on the downstream 

device, the device may not 

support the currently configured 

mapping mode. Use SDI3GLEVEL 

to change the mapping mode. 

3G Mapping 

Level SDIALT 

SDI 3G Level controls the 

mapping of the 3G-SDI signal 

when decoding 1080P50, 

1080P59.94 and 1080P60 

streams. The 3G-SDI signal can 

be mapped to Level A or Level B 

Dual Link. The mapping is 

individually configurable for each 

set of outputs (SDI and SDIALT). 

If 3G-SDI output does not 

appear on the downstream 

device, the device may not 

support the currently configured 

mapping mode. Use SDI3GLEVEL 

to change the mapping mode. 

A 
B 

Downscaling 

SDI 

The Downscaling SDI setting 

determines whether the SDI 

bank ( SDI Output 1 and 2 ) will 

be output natively or downscaled 

to SD. 

OFF 
SD 

Downscaling 

SDIALT 

The Downscaling SDI setting 

determines whether the SDI 

bank ( SDI Output 3 and 4 ) will 

be output natively or downscaled 

to SD. 

OFF 
SD 
 

Genlock Menu 

 

 

Genlock Mode 

Configures the genlock operation 
of the decoder.  SLAVE is 
primarily used for 3D 
applications and REMOTE is used 
in standard genlock operation. 

OFF - Disables genlock 
SLAVE - Enable Genlock, Decode 
source is synchronous to SYNC IN 
signal 
REMOTE - Enable genlock, Decode 
source is NOT synchronous to SYNC 
IN signal 

Horizontal 

Adjust 

Horizontal adjustment defines 

the difference in the SYNC IN 

HSYNC and output HSYNC. 

Typically, this should be in the 

range of 0 to +1 line in clocks. 

For example, a 1080I output 

could be adjusted from 0 to 

0 - 2200 

 

26

 

Summary of Contents for RD-71























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands