ABB tacteo KNX Product Manual Download Page 72 | Manualshive

Page: 72 / 187

ABB tacteo KNX Product Manual Download Page 72

Description of application and parameters

Application "Function block x"

Product manual 2CKA001473B9488

│72

11.5.4.7

Value for slats position down (%)

Options:

Setting option from 0 to 100 (%)

The parameter is used to set the position to which the slats of the linked blind are to open. The
associated 1-byte "Sx: slat position" communication object must hereby be connected with the
1-byte slat position object of the blind actuator.

Percentage values can be set in steps of 1%. Meaning of the percentage values:

■

0 % = slats completely open.

■

100 % = slats completely closed.

Note

The parameter can only be set if the "Blind/roller blind switchover function"
parameter is set on "Blind" and the "Object type" parameter is set on "1-byte 0-
100%.

11.5.4.8

Value for slats position down (%)

Options:

Setting option from 0 to 100 (%)

The parameter is used to set the position to which the slats of the linked blind are to close. The
associated 1-byte "Sx: slat position" communication object must hereby be connected with the
1-byte slat position object of the blind actuator.

Percentage values can be set in steps of 1%. Meaning of the percentage values:

■

0 % = slats completely open.

■

100 % = slats completely closed.

Note

The parameter can only be set if the "Blind/roller blind switchover function"
parameter is set on "Blind" and the "Object type" parameter is set on "1-byte 0-
100%.

«
...
70
71
72
73
74
...
»

Summary of Contents for tacteo KNX




























































































































































































Reviews:

No comments