manualshive.com logo in svg

ABB tacteo KNX, Product Manual, Page: 41 / 187

Share
Download
ABB tacteo KNX Product Manual Download Page 41

 

Description of application and parameters

Application "Device settings"

 

 

 

 

 

 

Product manual 2CKA001473B9488

│41

 

 

11.3 

Application "Device settings" 

11.3.1  Acoustic feedback signal - Application 

 

Options: 

Inactive 

 

Buzzer application 

 

■

 

Inactive: 
–  The application is not active. 

■

 

Buzzer application: 
–  The application is active. 

 

The application is used to specify whether an acoustic signal sounds when a button is pressed. 
This signal can be adapted individually after the activation. 

The following communication objects are available: 

■

 

"BUZ: object activation of acoustic feedback signal" 

■

 

"BUZ: triggering an alarm" 

■

 

"BUZ: time for automatic deactivation of the alarm" 

 

The communication objects are enabled via the associated parameters. 

 

 

Note 

The following parameters can only be adjusted when the function "Acoustic 
feedback signal" is set on "Buzzer application". 
The parameters for application "Acoustic feedback signal" can be called up via 

general parameters

. 

 

11.3.1.1 

Selected feedback signal noise is on 

 

Options: 

Click 

 

Beeping 

 

■

 

Clicking: 
–  "Clicking" sounds at the press of the buttons. 

■

 

Beeping: 
–  "Beeping" sounds at the press of the buttons. 

 

The parameter us used to specify the type of acoustic signal for the feedback signal noise. 

 

 

 

Summary of Contents for tacteo KNX




























































































































































































Reviews:

No comments