manualshive.com logo in svg

ABB tacteo KNX, Product Manual, Page: 162 / 187

Share
Download
ABB tacteo KNX Product Manual Download Page 162

 

Description of application and parameters

Application "General functions"

 

 

 

 

 

 

Product manual 2CKA001473B9488

│162

 

 

11.7.5.4 

Data flow direction 

 

Options: 

Input towards the output 

 

Output towards the input 

 

In both directions 

 

■

 

Input towards the output: 
–  Telegrams are transferred from object "GFx: input" to object "GFx: output". 

■

 

Output towards the input: 
–  Telegrams are transferred from object "GFx: output" to object "GFx: input". 

■

 

In both directions: 
–  Telegrams are transferred in both directions. 

 

The parameter is used to specify the direction in which the signal is to be transferred. 

 

11.7.5.5 

Enable object 

 

Options: 

Deactivated 

 

Activated 

 

■

 

Deactivated: 
–  Object "GFx: control input" is not enabled. 

■

 

Activated: 
–  Object "GFx: control input" is enabled. The function can be temporarily blocked via 

object "Sx: control input". 

 

The 1-bit communication object "GFx: control input" can be enabled with this parameter. 

 

 

Note 

If the "Enable object" parameter is activated, the following parameters can be 
set: 

■

 

"Object value enable object" 

■

 

"

Enable object after return of voltage" 

■

 

"

Save input signal" 

 

 

 

Summary of Contents for tacteo KNX




























































































































































































Reviews:

No comments