manualshive.com logo in svg

ABB tacteo KNX, Product Manual, Page: 42 / 187

Share
Download
ABB tacteo KNX Product Manual Download Page 42

 

Description of application and parameters

Application "Device settings"

 

 

 

 

 

 

Product manual 2CKA001473B9488

│42

 

 

11.3.1.2 

Acoustic feedback signal via object 

 

Options: 

Deactivated 

 

Activated 

 

■

 

Deactivated: 
–  The communication object is not enabled. 

■

 

Activated: 
–  The communication object is enabled. 

 

A 1-bit communication object "BUZ: object activation of acoustic feedback signal" can be 
enabled with this parameter. The further differentiation is carried out via the parameter that is 
available after enabling. 

 

11.3.1.3 

Activation of the acoustic feedback signal with 

 

Options: 

On telegram 

 

Off telegram 

 

■

 

ON telegram: 
–  Activation via On telegram. 

■

 

Off telegram: 
–  Activation via Off telegram. 

 

The parameter is used to specify whether the acoustic feedback signal is activated via the input 
object at the receipt of an On or an Off telegram. 

 

 

Note 

The parameter can only be set when parameter "Acoustic feedback signal via 
object" or parameter "Acoustic alarm via object" is activated. 

 

 

 

Summary of Contents for tacteo KNX




























































































































































































Reviews:

No comments