manualshive.com logo in svg

ABB tacteo KNX, Product Manual, Page: 65 / 187

Share
Download
ABB tacteo KNX Product Manual Download Page 65

 

Description of application and parameters

Application "Function block x"

 

 

 

 

 

 

Product manual 2CKA001473B9488

│65

 

 

11.5.2.2 

Reaction on falling edge 

 

Options: 

Deactivated 

 

Off 

 

On 

 

Alternating on/off 

 

■

 

Deactivated: 
–  No telegram is sent when the button is released. 

■ 

Off: 
–  The "Off" telegram is sent when the button is released (at falling edge). 

■

 

On: 
–  The "On" telegram is sent when the button is released (at falling edge). 

■

 

Alternating on/off: 
–  "On" and "Off" are sent alternately when the button is released. 

 

Application "1-button value switching" can differentiate between the press and the releasing of 
the button. A press is defined as "Rising edge" and the releasing as "Falling edge". 

The parameter is used to specify whether an On or Off telegram is sent on the bus at a falling 
edge via the 1-bit communication object "Sx: switching". A further option can be specified as to 
whether the switching telegrams are sent alternately. This means that after value "On" has been 
sent, "Off" is sent at a renewed release of the button. After it is released again, "On" is again 
sent out. 

 

 

 

Summary of Contents for tacteo KNX




























































































































































































Reviews:

No comments