manualshive.com logo in svg

ABB tacteo KNX, Product Manual, Page: 103 / 187

Share
Download
ABB tacteo KNX Product Manual Download Page 103

 

Description of application and parameters

Application "Function block x"

 

 

 

 

 

 

Product manual 2CKA001473B9488

│103

 

 

11.5.11.2 

Operating mode 

The possible options depend on parameter "Object type for output". 

Options for object type "1 bit": 

 

Options: 

Comfort 

 

Standby 

 

ECO 

 

Frost/heat protection 

 

■

 

Comfort: 
–  Switching signal "On" is sent via the 1-bit object and a linked RTC switches over into 

comfort mode. 

■

 

Standby: 
–  Switching signal "On" is sent via the 1-bit object and a linked RTC switches over into 

standby mode. 

■

 

ECO: 
–  Switching signal "On" is sent via the 1-bit object and a linked RTC switches over into 

ECO mode. 

■

 

Frost/heat protection: 
–  Switching signal "On" is sent via the 1-bit object and a linked RTC switches over into 

frost/heat protection mode. 

 

The parameter is used to specify the operating mode which is sent via communication object 
"Sx: operating mode" at the press of the button. 

 

 

 

Summary of Contents for tacteo KNX




























































































































































































Reviews:

No comments