ABB tacteo KNX Product Manual Download Page 44

Page: 44 / 187

Description of application and parameters

Application "Device settings"

Product manual 2CKA001473B9488

│44

11.3.1.6

Activation of the acoustic feedback signal with

Options:

On telegram

Off telegram

■

ON telegram:
– Activation via On telegram.

■

Off telegram:
– Activation via Off telegram.

The parameter is used to specify whether the acoustic feedback signal is activated via the input
object at the receipt of an On or an Off telegram.

Note

The parameter can only be set when parameter "Acoustic feedback signal via
object" or parameter "Acoustic alarm via object" is activated.

11.3.1.7

Alarm via the button

Options:

Deactivated

Activated

■

Deactivated:
– The pending alarm can not be deactivated with a press of the button.

■

Activated:
– The pending alarm can be deactivated with a press of the button.

Note

The parameter can only be set when parameter "Acoustic alarm via object" is
activated.

Summary of Contents for tacteo KNX




























































































































































































Search results

Summary of Contents for tacteo KNX

Reviews:

ABB tacteo KNX, Product Manual, Page: 44 / 187

Search results

Summary of Contents for tacteo KNX

Reviews: