manualshive.com logo in svg

ABB tacteo KNX, Product Manual, Page: 120 / 187

Share
Download
ABB tacteo KNX Product Manual Download Page 120

 

Description of application and parameters

Application "Function block x"

 

 

 

 

 

 

Product manual 2CKA001473B9488

│120

 

 

11.5.15  Application - 2-button value transmitter 

The application makes it possible to send preset values with a button pair via a joint 
communication object. 

The following communication object is available: 

■

 

"Sx: switching value" 

 

A telegram with value 1 is sent with the press of the first button. A telegram with value 2 is sent 
with the second button. Both values have the same bit size and are sent on the bus via the "Sx: 
switching value" communication object. The bit size is specified via the "Object type" parameter. 

The application makes a joint set of parameters and communication objects available in function 
block x for both buttons. 

 

 

Note 

The parameters for application "2-button value transmitter" can be called up via 

general parameters.

 

 
 
 

 

Note 

The number (S1 - Sx) of the object depends on the function block and the button 
number. 

 

 

 

Summary of Contents for tacteo KNX




























































































































































































Reviews:

No comments