manualshive.com logo in svg

ABB tacteo KNX, Product Manual, Page: 174 / 187

Share
Download
ABB tacteo KNX Product Manual Download Page 174

 

Description of application and parameters

Application "General functions"

 

 

 

 

 

 

Product manual 2CKA001473B9488

│174

 

 

11.7.7.8 

Overwrite delay time during download 

 

Options: 

Deactivated 

 

Activated 

 

■

 

Deactivated: 
–  The delay time will not be overwritten when the device is reprogrammed. 

■

 

Activated: 
–  The delay time will be overwritten when the device is reprogrammed. 

 

A telegram with a new delay time (s) can be received via the 2-byte communication object "GFx: 
delay time". The received 2-byte value is written to the memory of the device and is retained 
even after a power failure. 

The parameter is used to specify whether the received storage value is to be retained for a 
reprogramming of the device or replaced by the values specified in the parameterising software. 

 

 

 

Summary of Contents for tacteo KNX




























































































































































































Reviews:

No comments