3
W
ADDITIONAL SAFETY WARNINGS
- Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord.
Contact with a
“live” wire will make exposed metal parts of the tool “live” and shock the operator.
- To reduce the risk of injury. Operate the 3M Electric power tool with the 3M Power Supply.
Other types of power supplies may cause personal injury or
damage.
Tool Current
Extension Cord Length ft (m)
25 (7.6)
50 (15.2)
75 (22.8)
100 (30.4)
0 – 6 A
(mm
2
)
18 AWG
(1.0)
16 AWG
(1.5)
16 AWG
(1.5)
14 AWG
(2.5)
W
WARNING
To reduce the risks associated with impact from abrasive product, disc pad, or tool breakup, sharp edges, hazardous downforce, rupture, vibration and
noise:
• Only personnel who are properly trained should be allowed to service this tool.
• If you notice any abnormal noise or vibration when operating the tool, immediately discontinue its use and inspect for worn or damaged components. Correct
or replace the suspect component. If abnormal noise or vibration still exists, return the tool to 3M for repair or replacement. Refer to warranty instructions.
• Prior to use, inspect abrasive product and accessories for possible damage. If damaged, replace with new abrasive product and accessories available from
3M.
• Only use accessories supplied or recommended by 3M.
To reduce the risks associated with vibration:
• If any physical hand/wrist discomfort is experienced, work should be stopped promptly to seek medical attention. Hand, wrist and arm injury may result from
repetitive work, motion and overexposure to vibration.
To reduce the risks associated with loud noise:
• Always wear hearing protection while operating this tool. Follow your employer’s safety policy or local/national standards for personal protective equipment
requirements.
To reduce the risks associated with fi re or explosion:
• Do not operate the tool in explosive atmospheres, such as in the presence of fl ammable liquids, gases, or dust. The abrasives are able to create sparks when
working material, resulting in the ignition of the fl ammable dust or fumes.
• Refer to MSDS of material being worked as to potential for creating fi re or explosion hazard.
To reduce the risks associated with ingestion of harmful / toxic dusts from sanding surfaces such as lead painted surfaces, woods and metals:
• Contact with or inhalation of these dusts can endanger the health of operator and bystanders. Use appropriate personal protective equipment.
• Use appropriate respiratory and skin protection, or local exhaust as stated in the MSDS of the material being worked on.
W
CAUTION
To reduce the risk associated with environmental contamination:
• Do not throw electric power tools into the household waste! In accordance with the European Directive 2002/96/CE on Waste Electrical and Electronic
Equipment and transposition into national law, used electric power tools must be collected separately and recycled in an environmentally friendly manner.
• Separate collection of used products and packaging allows materials to be recycled. Use of recycled materials helps prevent environmental pollution and
reduces the demand for raw materials.
• Dispose of all the process dust in accordance with all applicable regulations.
To reduce the risks associated with fl y off of abrasive product or parts:
• Use care in attaching abrasive product and disc pad; following the instructions to ensure that they are securely attached to the tool before use.
• Never free spin the tool or otherwise allow it to be started unintentionally.
• Never point this product in the direction of yourself or another person, or start tool unintentionally.
• Never over-tighten accessory fasteners.
4
Parts List
38
39
52
22
37
1
2
3
24
23
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
30
32
33
25
26
28
35
36
44
45
46
47
49
51
50
31
40
41
43
42
27
29
35
34
48
4
53
38
