ZyXEL Communications OLT2406 Скачать руководство пользователя страница 75

Страница: 75 / 766

Chapter 5 Initial Setup Example

OLT2406 User’s Guide

Figure 43

Initial Setup Example: Management IP Address

Connect your computer to any Ethernet port on the OLT. Make sure your computer is in the same subnet
as the OLT.

Open your web browser and enter 192.168.1.1 (the default in-band IP address) in the address bar to
access the web configurator. See

Section 4.2 on page 64

for more information.

Click

Basic Setting

IP Setup

in the navigation

panel.

Configure the related fields in the

IP Setup

screen.

For the

VLAN2

network, enter 192.168.2.1 as the IP

address and 255.255.255.0 as the subnet mask.

In the

VID

field, enter the ID of the VLAN group to

which you want this management IP address to
belong. This is the same as the VLAN ID you
configure in the

Static VLAN

screen.

Click

Add

to save your changes back to the run-

time memory. Settings in the run-time memory are
lost when the OLT’s power is turned off.

Содержание OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание OLT2406

Отзывы:

Бренды по названию

Популярные бренды

ZyXEL Communications OLT2406, Руководство пользователя

Результаты поиска

Содержание OLT2406

Отзывы:

Бренды по названию

Популярные бренды