ZyXEL Communications OLT2406 Скачать руководство пользователя страница 205

Страница: 205 / 766

Chapter 25 Multicast

OLT2406 User’s Guide

205

25.3.1 IGMP Snooping VLAN

Click

Advanced Application > Multicast > Multicast Setting

in the navigation panel. Click the

IGMP

Snooping VLAN

link to display the screen as shown. See

IGMP Snooping and VLANs on page 198

for

more information on IGMP Snooping VLAN.

Figure 122

Advanced Application > Multicast > Multicast Setting > IGMP Snooping VLAN

The following table describes the labels in this screen.

Table 71 Advanced Application > Multicast > Multicast Setting > IGMP Snooping VLAN

LABEL

DESCRIPTION

Mode Select

auto

to have the OLT learn multicast group membership information of any VLANs

automatically.

Select

fixed

to have the OLT only learn multicast group membership information of the

VLAN(s) that you specify below.

In either

auto

fixed

mode, the OLT can learn up to 16 VLANs.

The OLT drops any IGMP control messages which do not belong to these 16 VLANs.

Apply

Click

Apply

to save your changes to the OLT’s run-time memory. The OLT loses these changes

if it is turned off or loses power, so use the

Save

link on the top navigation panel to save your

changes to the non-volatile memory when you are done configuring.

Cancel

Click

Cancel

to begin configuring this screen afresh.

VLAN

Use this section of the screen to add VLANs upon which the OLT is to perform IGMP snooping.

Name

Enter the descriptive name of the VLAN for identification purposes.

VID

Enter the ID of a static VLAN; the valid range is between 1 and 4094.

Add

Click this to create a new entry or to update an existing one.

This saves your changes to the OLT’s run-time memory. The OLT loses these changes if it is
turned off or loses power, so use the

Save

link on the top navigation panel to save your

changes to the non-volatile memory when you are done configuring.

Cancel

Click

Cancel

to reset the fields to your previous configuration.

Clear

Click

Clear

to reset the fields to the factory defaults.

Содержание OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание OLT2406

Отзывы:

Бренды по названию

Популярные бренды

ZyXEL Communications OLT2406, Руководство пользователя

Результаты поиска

Содержание OLT2406

Отзывы:

Бренды по названию

Популярные бренды