ZyXEL Communications OLT2406 Скачать руководство пользователя страница 273

Страница: 273 / 766

Chapter 31 ONT VoIP

OLT2406 User’s Guide

273

Figure 165

Advanced Application > ONT VoIP > VoIP Common Profile

The following table describes the labels in this screen.

Table 113 Advanced Application > ONT VoIP > VoIP Common Profile

LABEL

DESCRIPTION

Name

Type the name of the profile.

min local
port

max local
port

Specify a range (1-65535) of RTP ports to use for voice traffic.

dscp mark

Specify the Diffserv code point (from 0 to 63) to use for outgoing RTP packets.

piggyback

Select this to turn on RTP piggyback events on or clear it to turn them off.

tone

Select this to turn the handling of tones through RTP tone events according to RFC 4733 on or clear
it to turn it off.

Содержание OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание OLT2406

Отзывы:

Бренды по названию

Популярные бренды

ZyXEL Communications OLT2406, Руководство пользователя

Результаты поиска

Содержание OLT2406

Отзывы:

Бренды по названию

Популярные бренды