manualshive.com logo in svg

ZyXEL Communications OLT2406, Руководство пользователя

Поделиться
Скачать
ZyXEL Communications OLT2406 Скачать руководство пользователя страница 606

Chapter 83 OSPF Commands

OLT2406 User’s Guide

606

From the example above, the third octet of all the four network IP addresses is 8 (b00001000), 9 
(b00001001), 10 (b00001010), 11 (b000001011) respectively. The first 2 octec and the first 6 bits of the third 
octec (b000010) are the common part among these IP addresses. So 192.168.8.0/22 can be used to 
represent all of the 4 networks. The following example shows you how to configure the OSPF summary 
address and then show all redistribution entries.

sysname# config

sysname(config)# router ospf 172.16.1.1

sysname(config-ospf)# summary-address 192.168.8.0 255.255.252.0

sysname(config-ospf)# exit

sysname(config)# exit

sysname# show ip ospf database

OSPF Router with ID (172.16.1.1)

(Omit not external part °K)

                AS External Link States

Link ID         ADV Router      Age  Seq#       CkSum  Route

192.168.8.0     192.168.2.2        6 0x80000001 0xf209 E1 192.168.8.0/22 

Содержание OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды