manualshive.com logo in svg

ZyXEL Communications OLT2406, Руководство пользователя

Поделиться
Скачать
ZyXEL Communications OLT2406 Скачать руководство пользователя страница 121

OLT2406 User’s Guide

121

C

HAPTER

 10

Static MAC Forward Setup

10.1  Overview

This chapter discusses how to configure forwarding rules based on MAC addresses of devices on your 
network.

Use these screens to configure static MAC address forwarding.

10.1.1  What You Can Do

Use the 

Static MAC Forwarding

 screen (

Section 10.2 on page 121

) to assign static MAC addresses for a 

port.

10.2  Configuring Static MAC Forwarding  

A static MAC address is an address that has been manually entered in the MAC address table. Static 
MAC addresses do not age out. When you set up static MAC address rules, you are setting static MAC 
addresses for a port. This may reduce the need for broadcasting. 

Static MAC address forwarding together with port security allow only computers in the MAC address 
table on a port to access the OLT. See 

Chapter 20 on page 171

 for more information on port security.

Click 

Advanced Application 

>

 Static MAC Forwarding

 in the navigation panel to display the 

configuration screen as shown. 

Figure 75   

Advanced Application > Static MAC Forwarding 

Содержание OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды