ZyXEL Communications OLT2406 Скачать руководство пользователя страница 693 | Manualshive

Страница: 693 / 766

ZyXEL Communications OLT2406 Скачать руководство пользователя страница 693

Chapter 98 Port Protection Switching

OLT2406 User’s Guide

693

Figure 292

Downlink Port Protection Switching

The following section lists the commands for this feature.

Table 367 Downlink Port Protection Switching Commands

COMMAND

DESCRIPTION

M

P

show protect-switch pon status

Displays the current status of the downlink PON
port protection switching operation.

E

3

switch-over pon <

aid

>

Triggers a PON port protection switch-over
operation.

aid

: pon-<

slot

>-<

pon

>

E

13

protect-switch pon pon-<

slot

>-

<

port

> pon-<

slot

>-<

port

>

Assigns the specified downlink PON ports as an
active and backup pair. You can configure
multiple pairs of PON ports, but each PON port
can only be in one pair at a time.

pon pon-<slot>-<port>

is the active port, and

pon-<slot>-<port>

is the standby port.

C

13

Working path

Backup path

Traffic from

uplink

«
...
691
692
693
694
695
...
»

Содержание OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды