Zurich 56218 Скачать руководство пользователя страница 90

Страница: 90 / 101

Additional Tests

VIEWING DRIVE CYCLE PROCEDURES

For technical questions, please call 1-888-866-5797.

Red = Excessive over charging or under charging

If the alternator voltage is less than 9 V, the red, yellow and green

SYSTEM STATUS LEDs will flash on and off.

Choose

Main Menu

to return to the Main Menu.

VIEWING DRIVE CYCLE PROCEDURES

A Drive Cycle for a Monitor requires that the vehicle is driven in such a

way that all the required “Enabling Criteria” for the Monitor to run and

complete its diagnostic testing are met. You can use the Scan Tool to

view the Drive Cycle procedures for a selected Monitor.

While linked to a vehicle, press

The Main Menu displays.

Select

Drive Cycle Procedures

, then press

ENTER

A “One moment please…” message displays while the Scan Tool

retrieves Monitor status.

When Monitor status has been retrieved,

the Drive Cycle Procedures menu

displays. Depending on Monitor status,

you can view Drive Cycle procedures for

Monitors Incomplete

Monitors

Complete

If Drive Cycle Procedures are not
available for the vehicle, an
advisory message shows. Choose

Back

to return to the Main Menu.

Select

Monitors

Incomplete

Monitors Complete

, as desired, then

press

ENTER

A list of the available Monitors for the

selected status displays.

If no Monitors for the selected
status are detected, an advisory
message shows. Choose

Back

return to the Main Menu.

Select the Monitor for which you wish to view Drive Cycle Procedures,
then press

ENTER

A “One moment please…” message displays while the Scan Tool

retrieves the requested Drive Cycle Procedure. The Drive Cycle

Procedures screen for the Monitor displays when the procedure

has been retrieved.

If a Drive Cycle Procedure for the selected Monitor is not
available, an advisory message shows. Choose

Back

to return

to the Main Menu.

Содержание 56218






































































































Результаты поиска

Содержание 56218

Отзывы:

Похожие инструкции для 56218

Бренды по названию

Популярные бренды

Zurich 56218, Руководство пользователя

Результаты поиска

Содержание 56218

Отзывы:

Похожие инструкции для 56218

Бренды по названию

Популярные бренды