ZOE PPM3 Скачать руководство пользователя страница 186 | Manualshive

Страница: 186 / 214

background image

22-2

N i g h t i n g a l e P P M 3 U s e r ' s G u i d e

April 2019

Maintenance and Storage

PPM3 Function

Procedure

when plugged into mains power.

Speaker

Power-cycle the PPM3 and verify that the power-up speaker test tones are
generated.

Second Speaker

Power-cycle the PPM3 and verify that the power-up second speaker test
tones are generated.

ECG / Respiration

Connect ECG leads to Patient Simulator.

• Verify proper heart rate at 30 and 300 bpm (+/- 2 bpm or +/- 1%).

• Verify 1 mV test pulse (Lead II).

• Verify proper respiration rate at 15 and 120 bpm (+/- 3 bpm).

SpO

2

Connect to Patient Simulator (select appropriate sensor type).

• Verify proper SpO2 value at 84% and 96% (+/- 2%).

• Verify proper PR value at 30 and 240 bpm (+/- 5%).

NBP

NOTE: Do not allow system to remain pressurized and stable below 20
mmHg. The monitor will remove this pressure as a zero offset and this will
affect the validity of the calibration check.

NOTE: The following are required to perform this test: NIBP simulator or
sphygmomanometer along with a Y-adapter and a hand inflation bulb.

Pressure Accuracy Test:

Via the Service settings, put the NIBP in to

calibration mode. Set the pressure to 25 mmHg and 225 mmHg respectively
and verify that the pressure values reported by the PPM3 patient monitor
matches (±2 mmHg) of that reported on the simulator or
sphygmomanometer. Release pressure.

Overpressure Test:

Inflate cuff to 300 mmHg. Verify that the pressure is

automatically dumped at 300 +/- 30 mmHg.

Leak Test:

Inflate a cuff to 150 mmHg. Allow cuff pressure to settle (thermal

effect). Verify that the pressure drops less than 4 mmHg in 1 minute. Verify
that the pressure is automatically dumped after 180 seconds. Set the NIBP
back to normal mode. Power cycle the monitor.

Measurement Accuracy Test:

Connect to Patient Simulator and take a

NIBP measurement. Verify proper NIBP value at 120/80 (+/- 5 bpm).

«
...
184
185
186
187
188
...
»

Содержание PPM3























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PPM3

Бренд: Bahco Страницы: 9

Бренд: Garmin Страницы: 20

Бренд: Hakko Electronics Страницы: 8

Professional HS 8

Бренд: Hailo Страницы: 5

Бренд: Hainbuch Страницы: 52

Бренд: Pablo Страницы: 7

Бренд: Kamikaze Страницы: 112

Бренд: KAM Страницы: 2

Бренд: Labnet Страницы: 12

Accublock D1301

Бренд: Labnet Страницы: 13

Бренд: MAHA Страницы: 21

Бренд: MAGUIRE Страницы: 47

Chicken Coop Plan 3x5

Бренд: EASY COOPS Страницы: 21

Chicken Coop Plan 4x6

Бренд: EASY COOPS Страницы: 18

Chicken Coop Plan 8x10

Бренд: EASY COOPS Страницы: 18

Бренд: VelociRAX Страницы: 4

Бренд: ABM Страницы: 17

Бренд: Dantel Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды