ZOE PPM3 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 214

background image

4-4

N i g h t i n g a l e P P M 3 U s e r ' s G u i d e

April 2019

Respiration Monitoring

4.5. Respiration Monitoring Messages

Note

– Factory default RR alarm and limit settings may be found in the PPM3 Monitor

Settings chapter.

Message

Parameter

Value

Possible Cause

Suggested Action

RR < [lower limit]

[number]

The patient's respiration
rate has fallen below the
current lower alarm limit.

Check the patient and provide any
necessary clinical care.

Change the alarm limit if it is no longer
clinically appropriate.

RR > [upper limit]

[number]

The patient's respiration
rate has risen above the
current upper alarm limit.

Check the patient and provide any
necessary clinical care.

Change the alarm limit if it is no longer
clinically appropriate.

RR out of range (too high)

---

The patient's respiration
rate has risen above the
maximum value the
monitor can accurately
detect.

Electrical noise from
auxiliary equipment

Monitor confused by
signal artifact

Check the patient and provide any
necessary clinical care.

Isolate the patient from auxiliary
equipment, if possible.

Check to make sure electrodes are still
securely attached to the patient, and
reattach if necessary. Remember the
importance of good skin preparation
techniques.

RR lead off

[blank]

Unplugged cable

Broken cable

Loose lead wire

Faulty lead wire

Dried out electrode

Inoperable respiration
detection circuit

Intentional removal by
clinician

Check to make sure electrodes are still
securely attached to the patient, and
reattach if necessary. Remember the
importance of good skin preparation
techniques.

Check to make sure all the lead wires
are still connected to the electrodes.

Check to make sure the lead wires are
securely connected to the PPM3.

Check to make sure there are no
broken lead wires.

Press ALARM SILENCE in the event of
intentional removal by clinician.

Turn monitor off, then back on
If message persists, contact Zoe
technical support.

RR artifact

---

Patient movement

Electrical noise from
auxiliary equipment

Bad electrode contact

Calm the patient.

Isolate the patient from auxiliary
equipment, if possible.

Check to make sure electrodes are still
securely attached to the patient, and
reattach if necessary. Remember the
importance of good skin preparation
techniques.

«
...
54
55
56
57
58
...
»

Содержание PPM3























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PPM3

Бренд: Xo Страницы: 59

Бренд: Falcon Страницы: 8

Бренд: Federal Signal Corporation Страницы: 4

Бренд: ParaBody Страницы: 7

Бренд: HALDER Страницы: 2

Бренд: Hakko Electronics Страницы: 16

Бренд: Zell Страницы: 32

Бренд: Uflex Страницы: 16

Бренд: Hach Страницы: 456

Бренд: Sable Страницы: 28

Бренд: Beurer Страницы: 21

Бренд: SCHUNK Страницы: 35

Бренд: Marcy Страницы: 27

Бренд: Rocker Страницы: 23

Бренд: Western Global Страницы: 21

Бренд: König Electronic Страницы: 100

Бренд: Barkey Страницы: 72

Бренд: Amadas Страницы: 111

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды