manualshive.com logo in svg

ZOE PPM3, Руководство пользователя

Пользовательское руководство для продукта ZOE PPM3 теперь доступно для скачивания бесплатно на {сайт}. Это подробное руководство поможет вам разобраться с функционалом и настройками устройства. Не упустите возможность загрузить его прямо сейчас!

Поделиться
Скачать
background image

 

 

 

April 2019 

N i g h t i n g a l e   P P M 3   U s e r ' s   G u i d e  

24-11

 

                                                                                       

 

Technical Data 

Electromagnetic Compatibility (EMC) Information 

 

Medical electrical equipment requires special precautions regarding 
Electromagnetic Compatibility (EMC).  Portable and mobile Radio Frequency 
(RF) communications equipment can affect devices like the Nightingale PPM3. 
As such, the Nightingale PPM3 should not be used adjacent to other equipment. If 
this is not practical, then observe the Nightingale PPM3 to make sure it is 
operating properly after installation. 
 

 

Also, the use of accessories other than those recommended by Zoe Medical may 
result in increased EMC emissions or decreased EMC immunity of the 
Nightingale PPM3. 
 
 

Guidance and manufacturer’s declaration: electromagnetic emissions 

The Nightingale PPM3 is intended for use in the electromagnetic environment specified below. 
The user of the Nightingale PPM3 should assure that it is used in such an environment. 

Emissions test 

Compliance 

Electromagnetic environment / guidance 

RF emissions 
 
CISPR 11 

Group 1 

The Nightingale PPM3 uses RF energy only for its 
internal function. Therefore, its RF emissions are 
very low and are not likely to cause any 
interference in nearby electronic equipment. 

RF emissions 
 
CISPR 11 

Class B 

The Nightingale PPM3 is suitable for use in all 
establishments including domestic and those 
directly connected to the public low-voltage power 
supply network that supplies buildings used for 
domestic purposes. 

Harmonic emissions 
 
IEC 61000-3-2 

Class A 

Voltage fluctuations/ 
flicker emissions 
 
IEC 61000-3-3 

Complies 

 
 

Содержание PPM3























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PPM3

Varec 6700 Installation And Operation Instructions Manual preview
6700
Бренд: Varec Страницы: 74
Halyard MIC Series Instructions For Use Manual preview
MIC Series
Бренд: Halyard Страницы: 84
PAIDI Twist Instructions For Use Manual preview
Twist
Бренд: PAIDI Страницы: 48
C.M.O FL Series Instruction And Maintenance Manual preview
FL Series
Бренд: C.M.O Страницы: 10
NEC NEAX2400 ICS Installation Notes preview
NEAX2400 ICS
Бренд: NEC Страницы: 29
Dana Design ArcLight Quick Start Instructions preview
ArcLight
Бренд: Dana Design Страницы: 20
VBM POCKET Instructions For Use Manual preview
POCKET
Бренд: VBM Страницы: 36
W&H Med Lara Instructions For Use Manual preview
Lara
Бренд: W&H Med Страницы: 122
Native Instruments TRAKTOR KONTROL S4 User Manual preview
TRAKTOR KONTROL S4
Бренд: Native Instruments Страницы: 86
Native Instruments Maschine Reference Manual preview
Maschine
Бренд: Native Instruments Страницы: 245
Ocean Sonics icListen User Manual preview
icListen
Бренд: Ocean Sonics Страницы: 45
Össur i-Digits Access Instructions For Use Manual preview
i-Digits Access
Бренд: Össur Страницы: 231
JBM 54172 Instruction Manual preview
54172
Бренд: JBM Страницы: 13
DOTLUX FLOOReco 5164-040120 User Manual preview
FLOOReco 5164-040120
Бренд: DOTLUX Страницы: 10
Martin Maxedia 4 User Manual preview
Maxedia 4
Бренд: Martin Страницы: 202
Twiflex GMR-H Quick Start Manual preview
GMR-H
Бренд: Twiflex Страницы: 5
ALL-FILL VF100e Installation & Maintenance Manual preview
VF100e
Бренд: ALL-FILL Страницы: 32
Blatchford ESK+ Manual Knee Lock Instructions For Use Manual preview
ESK+ Manual Knee Lock
Бренд: Blatchford Страницы: 172

Бренды по названию

Популярные бренды

Загрузить еще бренды