manualshive.com logo in svg

Zippkits VBox 2013 Edition Deep Vee Sport Crackerbox, Инструкция по сборке

Поделиться
Скачать
Zippkits VBox 2013 Edition Deep Vee Sport Crackerbox Скачать руководство пользователя страница 12

 

 

12

 

 

Deck chines meet at nose. 

 

Install chines following angle of bulkhead. 

 

Lower chines meet at nose.  

When you are sure the joint is secure, glue in 
the bottom chines. 

 

They are done the same way, but the chine 
matches the bottom angle on all but the forward 
bulkhead 1. The chine will have to twist to 
accomplish this. It will lay flat (with relation to 
the bottom angle) on bulkheads 5, 4 and 3. 

At bulkhead 2, you can start the twist so that it 
meets the keel at the proper angle. 

Be sure that the chines are glued in so that 
they match the angle of the boat bottom. 
Bulkhead 1 is the only one where the chine 
does not match the angle of the bottom. 

Note how bottom chine matches bottom angle 
until BH 2. 

 

When that is secure, put some glue in the area 
where all of the chines meet at the nose, to give 
it a little extra strength. 

 

 

 

 

 

Time for another break. Give your beautiful boat 
skeleton at least 20 minutes to cure. 

 

Содержание VBox 2013 Edition Deep Vee Sport Crackerbox













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды