YOKOGAWA FLXA21 Скачать руководство пользователя страница 44

Страница: 44 / 64

<6. Function block parameters and Methods>

6-18

IM 12A01A02-72E

3rd Edition : Oct. 01, 2015-00

Error

Description and Remedy

NAMUR

NE107

category

DIAGNOSIS

(Classic)

DIAGNOSIS

(Condensed)

DIAGNOSIS

EXTENSION

Checksum error

Contact your local sales office.

Hardware

failure

electronics.

Failure of

the device or

armature

Electric

Failure

Sensor type not

correct

SENCOM sensor type is not

correct.

Change SENCOM sensor type

on the display of FLXA21.

Configuration

not valid

Failure of

the device or

armature

Configuration

Error

Internal error in

SENCOM

Replace SENCOM sensor.

Hardware

failure

electronics.

Failure of

the device or

armature

Sensor

Electric

Failure

SENCOM not

connected

SENCOM sensor is not

connected.

Check connection of SENCOM

sensor.

Hardware

failure

electronics.

Failure of

the device or

armature

Electric

Failure

EEPROM error

Write or read error in the

EEPROM.

Contact your local sales office.

Hardware

failure

electronics.

Failure of

the device or

armature

Electric

Failure

Sens. mod. not work Contact your local sales office.

Hardware

failure

electronics.

Failure of

the device or

armature

Electric

Failure

Table 6.6 DEVICE_STATUS_4 (FLXA21-PH: System Warning)

Error

Description and Remedy

NAMUR

NE107

category

DIAGNOSIS

(Classic)

DIAGNOSIS

(Condensed)

DIAGNOSIS

EXTENSION

Wash response time

failure

Half-value recovery time too long.

Check cleaning system. Adjust

timing parameters. Replace

measuring sensor.

—

Log Book (almost)

full

Logbook is more than 95% full.

Erase logbooks. Turn logbook

"full" warning off.

Maintenance

required

Maintenance

required

Warning for

Logbook

Calibration Due

System was not maintained

within the preset period. Perform

maintenance. Increase Calibr.

Interval.

Maintenance

required

Maintenance

required

Warning for

Calibration

Due

Содержание FLXA21

































































Результаты поиска

Содержание FLXA21

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA FLXA21, Руководство пользователя

Результаты поиска

Содержание FLXA21

Отзывы:

Бренды по названию

Популярные бренды