YOKOGAWA FLXA21 Скачать руководство пользователя страница 41

Страница: 41 / 64

<6. Function block parameters and Methods>

6-15

IM 12A01A02-72E

3rd Edition : Oct. 01, 2015-00

Table 6.3 DEVICE_STATUS_1

Error

Description and Remedy

NAMUR

NE107

category

DIAGNOSIS

(Classic)

DIAGNOSIS

(Condensed)

DIAGNOSIS

EXTENSION

Write Unlocked

Writing to parameters is

Unlocked.

Change the PB Write Lock(PB.

WRITE_LOCK) to Locked or turn

on the hardware write lock switch.

—

Hard Write Lock SW

OFF

Hardware write lock switch is

OFF.

Turn on the hardware write lock

switch.

—

Write Locked

Writing to parameters is locked.

Change the PB Write Lock(PB.

WRITE_LOCK) to Locked or turn

off the hardware write lock switch.

—

Hard Write Lock SW

OFF

Hardware write lock switch is ON.

Turn off the hardware write lock

switch.

—

Abnormal Boot

Process

Abnormal boot processing was

detected at the starting.

Check the cables and power.

—

Failure of

the device or

armature

—

PB in O/S Mode

(AL.40)

Physical Block is in O/S mode.

Change the PB Block Mode.

Target(PB.TARGET_MODE) to

Auto mode.

—

Function

Block Mode

Check

AMP Module

Failure2 (AL.02)

Amplifier EEPROM failed.

Replace electrical parts such

as the amplifier. Or replace the

device.

Hardware

failure

electronics.

Failure of

the device or

armature

Electric

Failure

Содержание FLXA21

































































Результаты поиска

Содержание FLXA21

Отзывы:

Похожие инструкции для FLXA21

Бренды по названию

Популярные бренды

YOKOGAWA FLXA21, Руководство пользователя

Результаты поиска

Содержание FLXA21

Отзывы:

Похожие инструкции для FLXA21

Бренды по названию

Популярные бренды