manualshive.com logo in svg

YOKOGAWA FLXA21, Руководство пользователя

Поделиться
Скачать
YOKOGAWA FLXA21 Скачать руководство пользователя страница 16

 

 

<3.  Getting Started>

3-3

IM 12A01A02-72E

3rd Edition : Oct. 01, 2015-00

3.5 

Notes When Using the FLXA21-SC 

Concentration Table (when using FieldMate)

The FLXA21-SC concentration table can be read from and written to using the CONC_TABLE_

CONCENTRATION_1 to CONC_TABLE_CONCENTRATION_21 and CONC_TABLE_

CONDUCTIVITY_1 to CONC_TABLE_CONDUCTIVITY_21 parameters of the transducer block.
However, when using FieldMate, note the following points.
The default concentration table values are “Not a Number”. On the device screen, they appear as 

blank. On FieldMate, “IEEE: NOT A NUMBER” is displayed.
Values set to “Not a Number” cannot be changed from FieldMate.
If you want to write the concentration table from FieldMate, first set all the items in the 

concentration table to some value from the device screen.

3.6 PRIMARY/SECONDARY/TERTIARY/

QUATERNARY_VALUE Value Assignment

Measurement values are assigned to PRIMARY_VALUE, SECONDARY_VALUE, TERTIARY_

VALUE, and QUATERNARY_VALUE from the device screen.
To set PRIMARY_VALUE, choose Commissioning > Output setup > Output, and then set the 

Process parameter item on the mA (Output) screen.
For others, choose Commissioning > Advanced setup > Communication > HART, and on the 

HART setup screen, set SECONDARY_VALUE with the SV item, TERTIARY_VALUE with the 

TV item, and QUATERNARY_VALUE with the QV item.

CAUTION

Be sure to use the default values for the following settings.
Changing them may disrupt communication.
 

Commissioning > Advanced setup > Communication screen

 

 

Default value:  HART

 

Commissioning > Advanced setup > Communication > HART setup screen

 

 

Item name: 

Network address

 

 

Default value:  0

If you want to change the settings from the device, first change Transducer Block Mode (refer 

also to tables in chapter 6 because not all parameters need OS to allow a change) to Out of 

Service.
If you want to load the factory settings or change the language, first change Physical Block Mode 

(refer also to tables in chapter 6 because not all parameters need OS to allow a change) to Out of 

Service.
Note that when you do, the FLXA21 will restart.

Содержание FLXA21

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды