YOKOGAWA FLXA21 Скачать руководство пользователя страница 22

Страница: 22 / 64

<4. Explanation of Basic Item>

4-6

IM 12A01A02-72E

3rd Edition : Oct. 01, 2015-00

4.5

Setting and change of basic parameters

This section describes the procedure taken to set and change the parameters for each block.

Obtaining access to each parameter differs depending on the configuration system used.
For details, refer to the instruction manual for each configuration system.

Set the Target of block mode (MODE_BLK) to Auto,

Man or O/S (*Note 2) according to the Write Mode of the

parameter to be set or changed.

When “actual mode” has changed (*Note 1),

data associated with the function block

can be maintenanced.

Access the block mode (MODE_BLK) of each block.

back to Auto (*Note 2).

Set the Target (*Note 1) of block mode

CAUTION

Do not turn the power of the device OFF immediately after parameter setting. When the

parameters are saved to the EEPROM, the redundant processing is executed for an

improvement of reliability. Should the power be turned OFF within 60 seconds after setting of

parameters, changed parameters are not saved and may return to their original values.

Refer to the tables in Chapter 6 for details of the Write Mode for each block.

AI Function Block Transducer Block

Physical Block

Automatic (Auto)

Yes

Manual (Man)

Yes

Out of Service (O/S)

Yes

Содержание FLXA21

































































Результаты поиска

Содержание FLXA21

Отзывы:

Похожие инструкции для FLXA21

Бренды по названию

Популярные бренды

YOKOGAWA FLXA21, Руководство пользователя

Результаты поиска

Содержание FLXA21

Отзывы:

Похожие инструкции для FLXA21

Бренды по названию

Популярные бренды