manualshive.com logo in svg

YASKAWA T1000A, Техническое руководство

Технический мануал YASKAWA T1000A - бесплатное руководство для пользователей, предоставляющее подробную информацию о продукте. Вы можете скачать его с manualshive.com и ознакомиться с инструкциями по эксплуатации. Идеальный выбор для тех, кто хочет получить всю необходимую информацию о данной модели.

Поделиться
Скачать
background image

6.6  Operator Programming Errors

YASKAWA ELECTRIC

 

SIEP C710616 30B YASKAWA AC Drive T1000A Technical Manual

 295

Tr

ouble

s

ho

ot

in

g

6

6.6

Operator Programming Errors

u

oPE Codes, Causes, and Possible Solutions

An Operator Programming Error (oPE) occurs when a contradictory parameter is set or an individual parameter is set to 
an inappropriate value.

The drive will not operate until the parameter or parameters causing the problem are set correctly. An oPE, however, does 
not trigger an alarm or fault output. If an oPE occurs, investigate the cause and 

Refer to oPE Codes, Causes, and 

Possible Solutions on page 295

 for the appropriate action. When an oPE appears on the operator display, press the 

ENTER button to view U1-18 and see the parameter that is causing the oPE error (U1-18).

Table 6.16  oPE Codes, Causes, and Possible Solutions

Digital Operator Display

Error Name

oPE01

Drive Capacity Setting Fault

Drive capacity and the value set to o2-04 do not match.

Cause

Possible Solutions

The drive model selection (o2-04) and the actual capacity of the drive are not the same.

Correct the value set to o2-04.

Digital Operator Display

Error Name

oPE02

Parameter Range Setting Error

Use U1-18 to find parameters set outside the range.

Cause

Possible Solutions

Parameters were set outside the possible setting range.

Set parameters to the proper values.

Note:

 When multiple errors occur at the same time, other errors are given precedence over oPE02.

Digital Operator Display

Error Name

oPE03

Multi-Function Input Selection Error

A contradictory setting is assigned to multi-function contact inputs H1-01 to H1-08.

Cause

Possible Solutions

• The same function is assigned to two multi-function inputs.
• Excludes “Not used” and “External Fault.”

• Ensure all multi-function inputs are assigned to different functions.
• Re-enter the multi-function settings to ensure this does not occur.

The Up command was set but the Down command was not, or vice versa (settings 10 vs. 11).

Correctly set functions that need to be enabled in combination with other functions.

• Run/Stop command for a 2-wire sequence was set (H1-

††

 = 42), but Forward/Reverse 

command (H1-

††

 = 43) was not.

• “Drive Enable” is set to multi-function input S1 or S2 (H1-01 = 6A or H1-02 = 6A).

Correctly set functions that need to be enabled in combination with other functions.

Two of the following functions are set at the same time:

• Up/Down Command (10 vs. 11)
• Hold Accel/Decel Stop (A)
• Offset Frequency 1, 2, 3 Calculations (44, 45, 46)

• Check if contradictory settings have been assigned to the multi-function input terminals at 

the same time.

• Correct setting errors.

The Up/Down command (10, 11) is enabled at the same time as PID control (b5-01).

Disable control PID (b5-01 = 0) or disable the Up/Down command.

Settings for N.C. and N.O. input for the following functions were selected at the same time:

• External Search Command 1 and External Search Command 2 (61 vs. 62)
• Fast Stop N.O. and Fast Stop N.C. (15 vs. 17)
• FWD Run Command (or REV) and FWD/REV Run Command (2-wire) (40, 41 vs. 42, 43)
• External DB Command and Drive Enable (60 vs. 6A)
• Synchronous Accel/Decel and Up/Down Command (or Accel/decel ramp hold) (51 vs. 10, 

11, A)

• DC Injection Braking 2 and Short Circuit Braking (N.O. or N.C.) (60 vs. 7C, 7D)

Check for contradictory settings assigned to the multi-function input terminals at the same 
time. Correct setting errors.

One of the following settings was entered while H1-

††

 = 2 (External Reference 1/2):

• b1-15 = 4 (Pulse Train Input) but the pulse train input selection is not set for the frequency 

reference (H6-01 > 0)

• b1-15 or b1-16 set to 3 but no option card is connected
• Although b1-15 = 1 (Analog Input) and H3-02 or H3-10 are set to 0 (Frequency Bias)

Correct the settings for the multi-function input terminal parameters.

H2-

††

 = 38 (Drive Enabled) but H1-

††

 is not set to 6A (Drive Enable).

H1-

††

 = 7E (Direction Detection) although H6-01 is not set to 3 (for V/f Control with PG 

using terminal RP as speed feedback input).

The following functions are set at the same time:

• H1-

††

=10 or 11 (Up/Down Command)

• H1-

††

=50 (Disturb Function Cancel), or S1-01=1 or 2 (Disturb Function Selection 

enabled)

Check for contradictory settings assigned to the multi-function input terminals and the 
parameter at the same time. Correct setting errors.

The following functions are set at the same time:

• b2-04 (DC Injection Braking Time at Stop) > 0
• b2-13 (Short Circuit Brake Time at Stop) > 0

Correct the parameter settings.

Digital Operator Display

Error Name

oPE04

Initialization required.

Cause

Possible Solutions

The drive, control board, or terminal board has been replaced and the parameter settings 
between the control board and the terminal board no longer match.

To load the parameter settings to the drive that are stored in the terminal board, set A1-03 to 
5550. Initialize parameters after drive replacement by setting A1-03 to 2220 or 3330.

Содержание T1000A






































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для T1000A

S-COM 7K Manual preview
7K
Бренд: S-COM Страницы: 400
EasyIO FG Series User Manual preview
FG Series
Бренд: EasyIO Страницы: 12
RMG GSM 3ST User Manual preview
GSM 3ST
Бренд: RMG Страницы: 6
BADODOSECURITY G200 Quick Manual preview
G200
Бренд: BADODOSECURITY Страницы: 8
halstrup-walcher PSD4 Series Instruction Manual preview
PSD4 Series
Бренд: halstrup-walcher Страницы: 39
Linear Technology LT8570 Demo Manual preview
LT8570
Бренд: Linear Technology Страницы: 7
YASKAWA J1000 CIMR-JC series Installation Manual preview
J1000 CIMR-JC series
Бренд: YASKAWA Страницы: 25
Grundfos IO 401 Installation And Operating Instructions Manual preview
IO 401
Бренд: Grundfos Страницы: 20
FrSky R9M Instruction Manual preview
R9M
Бренд: FrSky Страницы: 2
IBA ibaMS16-DI-220V Series Manual preview
ibaMS16-DI-220V Series
Бренд: IBA Страницы: 32
Cypress CY8C28 series Technical Reference Manual preview
CY8C28 series
Бренд: Cypress Страницы: 571
Conductrix Wampfler 0832 Installation Instructions Manual preview
0832
Бренд: Conductrix Wampfler Страницы: 23
Carel E2V Installation preview
E2V
Бренд: Carel Страницы: 2
Timotion TBB5 User Manual preview
TBB5
Бренд: Timotion Страницы: 9
Baby Trend TJ68 Instruction Manual preview
TJ68
Бренд: Baby Trend Страницы: 22
Rare Waves Grendel 2TAC Manual preview
Grendel 2TAC
Бренд: Rare Waves Страницы: 18
YASKAWA MP2600iec Hardware Manual preview
MP2600iec
Бренд: YASKAWA Страницы: 42
YASKAWA MP210 Series User Manual preview
MP210 Series
Бренд: YASKAWA Страницы: 351

Бренды по названию

Популярные бренды

Загрузить еще бренды