YASKAWA HV600, Установка и запуск

Страница: 200 / 310

7.8 H: Terminal Functions
200 YASKAWA TOEPYAIH6B01A HV600 AC Drive Narrow Bypass Installation & Startup
Setting Value Function Description
9 Frequency Reference from
Keypad Shows the selected frequency reference source.
ON : The keypad is the frequency reference source.
OFF : Parameter b1-01 [Frequency Reference Selection 1] is the frequency reference source.
B Torque Detection 1 (N.O.) The terminal activates when the drive detects overtorque or undertorque.
ON : The output current/torque > L6-02 [Torque Detection Level 1] , or the output current/torque < L6-02 for longer than the time set
in L6-03 [Torque Detection Time 1] .
C Frequency Reference Loss The terminal activates when the drive detects a loss of frequency reference.
E Fault The terminal activates when the drive detects a fault.
Note:
The terminal will not activate for CPF00 and CPF01 [Control Circuit Error] faults.
F
Not Used Use this setting for unused terminals or to use terminals in through mode. Also use this setting as the PLC contact output via
MEMOBUS/Modbus or the communication option. This signal does not function if signals from the PLC are not configured.
10 Alarm The terminal activates when the drive detects a minor fault.
11 Fault Reset Command
Active The terminal activates when the drive receives the Reset command from the control circuit terminal, serial communications, or the
communication option.
12 Timer Output Use this setting when the drive uses the timer function as an output terminal.
13 Speed Agree 2 The terminal activates when the output frequency is in the range of the frequency reference ± L4-04 [Speed Agree Detection Width
(+/-)] .
Note:
The detection function operates in the two motor rotation directions.
ON : The output frequency is in the range of “ frequency reference ± L4-04 ” .
OFF : The output frequency is not in the range of “ frequency reference ± L4-04 ” .
14 User-Set Speed Agree 2 The terminal activates when the output frequency is in the range of L4-03 [Speed Agree Detection Level (+/-)] ± L4-04 [Speed
Agree Detection Width (+/-)] and in the range of the frequency reference ± L4-04 .
Note:
The detection level set in L4-03 is a signed value. The drive will only detect in one direction.
ON : The output frequency is in the range of “ L4-03 ± L4-04 ” and the range of frequency reference ± L4-04 .
OFF : The output frequency is not in the range of “ L4-03 ± L4-04 ” or the range of frequency reference ± L4-04 .
15 Frequency Detection 3 The terminal deactivates when the output frequency >
“
L4-03 [Speed Agree Detection Level (+/-)] + L4-04 [Speed Agree Detection
Width (+/-)] ” . After the terminal deactivates, the terminal stays deactivated until the output frequency is at the value of L4-03 .
Note:
The detection level set in L4-03 is a signed value. The drive will only detect in one direction.
ON : The output frequency < L4-03 , or the output frequency ≤ L4-03 + L4-04 .
OFF : The output frequency >
“
L4-03 + L4-04
”
.
16 Frequency Detection 4 The terminal activates when the output frequency > L4-03 [Speed Agree Detection Level (+/-)] . After the terminal activates, the
terminal stays activated until the output frequency is at the value of “ L4-03 - L4-04 ” .
Note:
The detection level set in L4-03 is a signed value. The drive will only detect in one direction.
ON : The output frequency > L4-03 .
OFF : The output frequency <
“
L4-03 - L4-04
”
, or the output frequency ≤ L4-03 .
17 Torque Detection 1 (N.C.) The terminal deactivates when the drive detects overtorque or undertorque.
OFF : The output current/torque > L6-02 [Torque Detection Level 1] , or the output current/torque < L6-02 for longer than the time
set in L6-03 [Torque Detection Time 1] .
18 Torque Detection 2 (N.O.) The terminal activates when the drive detects overtorque or undertorque.
ON : The output current/torque > L6-05 [Torque Detection Level 2] , or the output current/torque < L6-05 for longer than the time set
in L6-06 [Torque Detection Time 2] .
19 Torque Detection 2 (N.C.) The terminal deactivates when the drive detects overtorque or undertorque.
OFF : The output current/torque > L6-05 [Torque Detection Level 2] , or the output current/torque < L6-05 for longer than the time
set in L6-06 [Torque Detection Time 2] .
1A During Reverse The terminal activates when the motor operates in the reverse direction.
ON : The motor is operating in the reverse direction.
OFF : The motor is operating in the forward direction or the motor stopped.
1B During Baseblock (N.C.) The terminal deactivates during baseblock. When the drive is in baseblock, the drive output transistor stops switching and does not
make DC bus voltage.
ON : The drive is not in baseblock.
OFF : During baseblock
1E Executing Auto-Restart The terminal activates when the Auto Restart function is trying to restart after a fault.
1F Motor Overload Alarm
(oL1) The terminal activates when the electronic thermal protection value of the motor overload protective function is a minimum of 90%
of the detection level.
20 Drive Overheat Pre-Alarm
(oH) The terminal activates when the drive heatsink temperature is at the level set with L8-02 [Overheat Alarm Level] .