YASKAWA 050-1BA00 Скачать руководство пользователя

Страница: 57 / 63

The

pulse duration

defines how long the output is set. It may be

preset in steps of 2.048ms between 0 and 522.24ms. The

pulse dura-

tion

starts with the setting of the according digital output. The inac-

curacy of the

pulse duration

is less than 2.048ms. There is no past

triggering of the

pulse duration

when the

comparison value

has been

left and reached again during pulse output.

The bit STS_DO is set together with the bit STS_CMP in

the counter status. In contrast to the bit STS_DO this bit

remains set as long as it is reset by setting the bit

RES_SET in the control word.

The

hysteresis

serves the avoidance of many toggle processes of

the output and the interrupt, if the

counter value

is in the range of

the

comparison value

For the hysteresis you may set a range of 0 to 255.

The settings 0 and 1 deactivate the

hysteresis

The

hysteresis

influences zero run, comparison, over- and under-

flow.

An activated

hysteresis

remains active after a change. The new

hysteresis

range is activated with the next

hysteresis

event.

The following pictures illustrate the output behavior for

hysteresis

and

hysteresis

3 for the according conditions:

Counter value

comparison value

output is set and

hysteresis

activated

2 Leave

hysteresis

range

output is reset

Counter value

comparison value

output is set and

hysteresis

activated

4 Leave

hysteresis

range, output remains set for

counter value

comparison value

counter value

comparison value

and

hysteresis

active

output

is reset

counter value

comparison value

output is not set for

hyste-

resis

active

7 Leave

hysteresis

range, output remains set for

counter value

comparison value

Hysteresis

Effect at counter value

comparison value

VIPA System SLIO FM 050

Deployment

Counter additional functions

HB300 | FM | 050-1BA00 | GB | 15-11

Содержание 050-1BA00
































































Результаты поиска

Содержание 050-1BA00

Отзывы:

Похожие инструкции для 050-1BA00

Бренды по названию

Популярные бренды

YASKAWA 050-1BA00, Руководство пользователя

Результаты поиска

Содержание 050-1BA00

Отзывы:

Похожие инструкции для 050-1BA00

Бренды по названию

Популярные бренды