YASKAWA 050-1BA00 Скачать руководство пользователя

Страница: 54 / 63

The activation res. de-activation of the counter happens via an

internal gate (I gate). The I gate is the AND operation of the software

gate (SW gate) and the hardware gate (HW gate). The

SW gate

opened (activated) via your user application by an edge 0-1 of the bit

SW_GATE_SET of CCTRL_I in the

output area

. The

software

gate is

closed (de-activated) by an edge 0-1 of the bit SW_GATE_RESET.

The HW gate is controlled via the concerning "Gate" input. The

parameterization allows you to de-activate the consideration of the

gate so that the counter activation can take place only via the

gate. The following states influence the I gate:

SW gate

HW gate

influences

I gate

with edge 0-1

de-activated

Gate function abort and interrupt

The parameterization defines if the gate interrupts or aborts the

counter process.

abort function

the counter starts counting with the

load value

after gate restart.

Gate function

VIPA System SLIO FM 050

Deployment

Counter additional functions

HB300 | FM | 050-1BA00 | GB | 15-11

Содержание 050-1BA00
































































Результаты поиска

Содержание 050-1BA00

Отзывы:

Похожие инструкции для 050-1BA00

Бренды по названию

Популярные бренды

YASKAWA 050-1BA00, Руководство пользователя

Результаты поиска

Содержание 050-1BA00

Отзывы:

Похожие инструкции для 050-1BA00

Бренды по названию

Популярные бренды