YASKAWA 050-1BA00 Скачать руководство пользователя

Страница: 25 / 63

The electronic power section supply is internally protected

against higher voltage by fuse. The fuse is within the

power module. If the fuse releases, its electronic module

must be exchanged!

The power section supply is to be externally protected with a fuse,

which corresponds to the maximum current. This means max. 10A

is to be protected with a 10A fuse (fast) respectively by a line cir-

cuit breaker 10A characteristics Z!

It is recommended to externally protect the electronic power

supply for bus coupler and I/O area with a 2A fuse (fast) respec-

tively by a line circuit breaker 2A characteristics Z.

The electronic power supply for the I/O area of the power module

007-1AB10 should also be externally protected with a 1A fuse

(fast) respectively by a line circuit breaker 1A characteristics Z.

After PowerON of the System SLIO the LEDs RUN respectively MF

get on so far as the sum current does not exceed 3A.
With a sum current greater than 3A the LEDs may not be activated.
Here the power module with the order number 007-1AB10 is to be

placed between the peripheral modules.

If the 10A for the power section supply is no longer sufficient, you

may use the power module from VIPA with the order number

007-1AB00. So you have also the possibility to define isolated

groups.
The power module with the order number 007-1AB10 is to be used if

the 3A for the electronic power supply at the backplane bus is no

longer sufficient. Additionally you get an isolated group for the DC

24V power section supply with 4A.
By placing the power module 007-1AB10 at the following backplane

bus modules may be placed with a sum current of max. 2A. After-

wards the power module 007-1AB10 is to be placed again. To secure

the power supply, the power modules may be mixed used.

Fusing

State of the electronic

power supply via LEDs

Deployment of the

power modules

Power module

007-1AB00

VIPA System SLIO FM 050

Basics and Assembly

Wiring

HB300 | FM | 050-1BA00 | GB | 15-11

Содержание 050-1BA00
































































Результаты поиска

Содержание 050-1BA00

Отзывы:

Похожие инструкции для 050-1BA00

Бренды по названию

Популярные бренды

YASKAWA 050-1BA00, Руководство пользователя

Результаты поиска

Содержание 050-1BA00

Отзывы:

Похожие инструкции для 050-1BA00

Бренды по названию

Популярные бренды