background image

4TNV98 & 4TNE98 Diesel Engine 

 

Section 2. Periodic Maintenance 

37

 

CAUTION 

Observe the following environmental operating 
conditions to maintain engine performance and 
avoid premature engine wear: 
• Avoid operating in extremely dusty conditions. 
• Avoid operating in the presence of chemical 

gases or fumes. 

• Avoid operating in a corrosive atmosphere 

such as salt water spray. 

• NEVER install the engine in a floodplain 

unless proper precautions are taken to avoid 
being subject to a flood. 

• NEVER expose the engine to the rain. 

 

 

CAUTION 

Observe the following environmental operating 
conditions to maintain engine performance and 
avoid premature engine wear: 
• The standard range of ambient temperatures 

for the normal operation of Yanmar engines is 
from +5°F (-15°C) to +113°F (+45°C). 

• If the ambient temperature e113°F 

(+45°C) the engine may overheat and cause 
the engine oil to break down. 

• If the ambient temperature is below +5°F (-

15°C) the engine will be hard to start and the 
engine oil may not flow easily. 

• Contact your authorized Yanmar industrial 

engine dealer or distributor if the engine will 
be operated outside of this standard 
temperature range. 

 

 

CAUTION 

NEVER hold the key in the START position for 
longer than 15 seconds or the starter motor will 
overheat. 

 

 

CAUTION 

For maximum engine life, Yanmar recommends 
that when shutting the engine down, you allow 
the engine to idle, without load, for five minutes. 
This will allow the engine components that 
operate at high temperatures, such as the 
turbocharger (if equipped) and exhaust system, 
to cool slightly before the engine itself is shut 
down. 

 

 

CAUTION 

NEVER use an engine starting aid such as ether. 
Engine damage will result. 

 

 

CAUTION 

Make sure the engine is installed on a level 
surface. If a continuously running engine is 
installed at an angle greater than (IDI = 25°, DI = 
30°) in any direction or if an engine runs for 
short periods of time (less than three minutes) 
at an angle greater than (IDI = 30°, DI = 35°) in 
any direction, engine oil may enter the 
combustion chamber causing excessive engine 
speed and white exhaust smoke. This may 
cause serious engine damage. 

 

Содержание 4TNV98























































































































































































































































Отзывы: