Yanmar 4TNV98 Скачать руководство пользователя | Manualshive

Страница: 18 / 246

background image

4TNV98 & 4TNE98 Diesel Engine

Section 1. General Service Information

16

Engine Oil

CAUTION

Only use the engine oil specified.
Other engine oils may affect warranty coverage,
cause internal engine components to seize and /
or shorten engine life.
Prevent dirt and debris from contaminating the
engine oil. Carefully clean the oil cap / dipstick
and the surrounding area before you remove the
cap.
NEVER mix different types of engine oil. This
may adversely affect the lubricating properties
of the engine oil.
NEVER overfill. Overfilling may result in white
exhaust smoke, engine overspeed or internal
damage.

Engine Oil Specifications

Use an engine oil that meets or exceeds the
following guidelines and classifications:

Service Categories

• API Service Categories CD or higher

• ACEA Service Categories E-3, E-4, and E-5

• JASO Service Category DH-1

Definitions

• API Classification (American Petroleum Institute)

• ACEA Classification (Association des

Constructeurs Européens d'Automobilies)

• JASO (Japanese Automobile Standards

Organization)

NOTE:

• Be sure the engine oil, engine oil storage

containers, and engine oil filling equipment arefree
of sediment and water.

• Change the engine oil after the first 50 hours of

peration and then every 500 hours thereafter.

• Select the oil viscosity based on the ambient

temperature where the engine is being operated.
See the SAE Service Grade Viscosity Chart

(Figure 4-4a)

• Yanmar does not recommend the use of engine oil

“additives.”

Additional Technical Engine Oil
Requirements:

The engine oil must be changed when the Total
Base Number (TBN) has been reduced to 1.0
mgKOH /g test method; JIS K-201-5.2-2 (HCI),
ASTM D4739 (HCI).

Engine Oil Viscosity

Select the appropriate engine oil viscosity based on
the ambient temperature and use the SAE Service
Grade Viscosity Chart in

Figure 4-4a.

Figure 4-4a

«
...
16
17
18
19
20
...
»

Содержание 4TNV98























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 4TNV98

Vickers M2-200 Series

Бренд: Eaton Страницы: 13

Electric Motor G2909

Бренд: Grizzly Страницы: 2

Бренд: Navistar Страницы: 24

Бренд: Stuart Turner Страницы: 20

GSX-R 1300 Turbo

Бренд: RPE Страницы: 19

Бренд: Reely Страницы: 4

Бренд: MTD Страницы: 32

Бренд: Lombardini Страницы: 50

Бренд: Lombardini Страницы: 114

Бренд: Lycoming Страницы: 74

Бренд: YS Страницы: 2

Бренд: Detroit Diesel Страницы: 195

Бренд: Coleman Страницы: 79

Бренд: Honda Страницы: 2

Бренд: Honda Страницы: 32

Бренд: Honda Страницы: 56

GX 610 standard

Бренд: Honda Страницы: 69

B&W S50MC-C8-TII

Бренд: Man Страницы: 403

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды