background image

 

4TNV98 & 4TNE98 Diesel Engine

 

Section 2. Periodic Maintenance

 

50

Check Battery   

 

 DANGER 

 
 
 

EXPLOSION HAZARD! 

NEVER check the remaining battery  charge by 
shorting out the terminals. This will result in a 
spark and may cause an explosion or fire. Use a 
hydrometer to check the remaining battery 
charge. 
If the electrolyte is frozen, slowly warm the 
battery before you recharge it. 
Failure to comply will result in death or serious 
injury. 

 

 

 WARNING 

 
 
 

BURN HAZARD! 

Batteries contain sulfuric acid. NEVER allow 
battery fluid to come in contact with clothing, 
skin or eyes. Severe burns could result. 
ALWAYS wear safety goggles and protective 
clothing when servicing the battery. If battery 
fluid contacts the eyes and / or skin, 
immediately flush the affected area with a large 
amount of clean water and obtain prompt 
medical treatment. 
Failure to comply could result in death or 
serious injury. 

 

 
 
 
 
 
 
 
 
 
 
 
 

 CAUTION 

 
 
 
 

ALWAYS be environmentally responsible.   
Follow the guidelines of the EPA or other 
governmental agencies for the proper disposal 
of hazardous materials such as engine oil, 
diesel fuel and engine coolant. Consult the local 
authorities or reclamation facility. 
NEVER dispose of hazardous materials 
irresponsibly by dumping them into a sewer, on 
the ground, or into ground water or waterways. 
Failure to follow these procedures may 
seriously harm the environment. 

 

When the amount of fluid nears the lower limit 

(Figure 5-8, (1))

, fill with distilled water 

(Figure 5-8, 

(2))

 so it is at the upper limit 

(Figure 5-8, (3))

. If 

operation continues with insufficient battery fluid, 
the battery life is shortened, and the battery may 
overheat and explode. During the summer, check 
the fluid level more often than specified.   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Figure 5-8   

 
If the engine cranking speed is so slow that the 
engine does not start, recharge the battery.   
 
If the engine still will not start after charging, have 
your authorized Yanmar industrial engine dealer or 
distributor check the battery and the engine’s 
starting system.   
 

Содержание 4TNV98























































































































































































































































Отзывы: