Yanmar 4TNV98 Скачать руководство пользователя | Manualshive

Страница: 21 / 246

background image

4TNV98 & 4TNE98 Diesel Engine

Section 1. General Service Information

19

Engine Coolant Specifications

Use a Long Life Coolant (LLC) or an Extended Life
Coolant (ELC) that meets or exceeds the following
guidelines and specifications:

Additional Technical Coolant
Specifications:

• ASTM D6210, D4985 (US)

• JIS K-2234 (Japan)

• SAE J814C, J1941, J1034 or J2036 (International)

Alternative Engine Coolant

If an Extended or Long Life Coolant is not available,
alternatively, you may use an ethylene glycol or
propylene glycol based conventional coolant
(green).

Notes:

• ALWAYS use a mix of coolant and water. NEVER use water

only.

• Mix the coolant and water per the mixing instructions on the

coolant container.

• Water quality is important to coolant performance. Yanmar

recommends that soft, distilled, or demineralized water be
used to mix with coolants.

• NEVER mix extended or long life coolants and conventional

(green) coolants.

• NEVER mix different types and / or colors of extended life

coolants.

• Replace the coolant every 1000 engine hours or once a year.

Filling Radiator with Engine Coolant

Fill the radiator and reserve tank as follows. This
procedure is for filling the radiator for the first time
or refilling it after it is flushed. Note that a typical
radiator is illustrated

(Figure 4-6).

Figure 4-6

1.

Check to be sure the radiator drain plug

isinstalled and tightened or the drain cock

(Figure

4-6, (1))

is closed. Also make sure thecoolant

drain plug

(Figure 4-7, (1))

in thecylinder block is

closed or the oil coolant hoses

(Figure 4-8, (1))

are installed at the oil cooler.

Figure 4-7

«
...
19
20
21
22
23
...
»

Содержание 4TNV98























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 4TNV98

3T-MOTORS 3T45-20

Бренд: 3T-Components Страницы: 24

Бренд: Quick Fuel Technology Страницы: 5

MICROPUMP DEELE

Бренд: Idex Страницы: 23

Бренд: Scania Страницы: 83

Бренд: Sumoto Страницы: 20

Бренд: Flux Страницы: 20

Бренд: KONTRONIK Страницы: 6

Бренд: Reely Страницы: 4

2005 ENDUCROSS EC 125

Бренд: GAS GAS Страницы: 50

Бренд: Saito Страницы: 2

Бренд: Saito Страницы: 2

Бренд: Saito Страницы: 7

Бренд: Hatz Страницы: 94

Бренд: Hino Motors Страницы: 339

Бренд: YS Страницы: 2

Бренд: YS Страницы: 2

Бренд: MULTIPLEX modell Страницы: 6

Бренд: Motion Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды