Yanmar 4TNV98 Скачать руководство пользователя | Manualshive

Страница: 14 / 246

background image

Section 1. Component Identification

12

Diesel Fuel

Diesel Fuel Specifications

Diesel fuel should comply with the following
specifications. The table lists several worldwide
specifications for diesel fuels.
.

Diesel Fuel
Specification

Location

No. 2-D, No. 1-D,
ASTM D975-94

USA

EN590:96

European
Union

ISO 8217 DMX

International

BS 2869-A1 or A2

United
Kingdom

JIS K2204 Grade No.
2

Japan

KSM-2610 Korea

GB252 China

Additional Technical Fuel Requirements

• The fuel cetane number should be equal to 45 or higher.

• The sulfur content must not exceed 0.5% by volume. Less

than 0.05% is preferred.

• Bio-Diesel fuels. See Bio-Diesel Fuels on page 4-9.

• NEVER mix kerosene, used engine oil, or residual fuels with

the diesel fuel.

• The water and sediment in the fuel should not exceed 0.05%

by volume.

• Keep the fuel tank and fuel-handling equipment clean at all

times.

• Poor quality fuel can reduce engine performance and / or

cause engine damage.

• Fuel additives are not recommended. Some fuel additives may

cause poor engine performance. Consult your Yanmar
representative for more information.

• The ash content must not exceed 0.01% by volume.

• The carbon residue content must not exceed 0.35% by volume.

Less than 0.1% is preferred.

• The total aromatics content should not exceed 35% by volume.

Less than 30% is preferred.

• The PAH (polycyclic aromatic hydrocarbons) content should

be below 10% by volume.

• The metal content of Na, Mg, Si, and Al should be equal to or

lower than 1 mass ppm. (Test analysis method JPI-5S-44-95)

• Lubricity: The wear mark of WS1.4 should be Max. 0.018 in

(460

μ

m) at HFRR test.

Bio-Diesel Fuels

In Europe and in the United States, as well as some
other countries, non-mineral oil based fuel
resources such as RME (Rapeseed Methyl Ester)
and SOME (Soybean Methyl Ester), collectively
known as FAME (Fatty Acid Methyl Esters), are
being used as extenders for mineral oil derived
diesel fuels.

Yanmar approves the use of bio-diesel fuels that do
not exceed a blend of 5% (by volume) of FAME with
95% (by volume) of approved mineral oil derived
diesel fuel. Such bio-diesel fuels are known in the
marketplace as B5 diesel fuels.

These B5 diesel fuels must meet certain
requirements.

1.

The bio-fuels must meet the minimum

specifications for the country in which they
areused.

• In Europe, bio-diesel fuels must comply with the European

Standard EN14214.

• In the United States, bio-diesel fuels must comply with the

American Standard ASTM D-6751.

2.

Bio-fuels should be purchased only from

recognized and authorized diesel fuel suppliers.

«
...
12
13
14
15
16
...
»

Содержание 4TNV98























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 4TNV98

Бренд: Parker Страницы: 36

Бренд: Briggs & Stratton Страницы: 20

Бренд: SOMFY Страницы: 7

24 v High Performance Synchronous Motor

Бренд: Rega Страницы: 1

Бренд: Northern Lights Страницы: 36

Бренд: Northern Lights Страницы: 45

Бренд: Northern Lights Страницы: 56

Бренд: Forest-Master Страницы: 16

Бренд: Metronic Страницы: 28

A50-10L Turnado

Бренд: Hacker Страницы: 4

Бренд: Hacker Страницы: 36

Бренд: WÜRGES Страницы: 4

Бренд: Volvo Страницы: 25

Бренд: Robin America Страницы: 36

Бренд: O.S. engine Страницы: 4

O.S. Max-160FXRing

Бренд: O.S. engine Страницы: 10

Бренд: Barrus Страницы: 100

Бренд: DLE Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды