![background image](http://html1.mh-extra.com/html/somfy/orea-rts/orea-rts_programming-and-limit-setting-instructions_1317818001.webp)
Power Supply
Description
Transmitters
Pictured below are all compatible controls
1
2
Motor's memory capacity with Telis, Decora RTS, Telis Soliris: maximum of 12 transmitters
plus and additional 3 RTS sensors.
A.
All motor feedback (previously audible "beeping") is now replaced by a visual jog. A jog is a short Up & Down movement of the motor
(0.5 second turn of the motor in each direction).
For initial programming provide power only to the motor being programmed.
B.
C. The OREA RTS motor in Factory Mode will not respond to any transmitter until a transmitter is assigned to communicate with the motor's
receiver. To assign a transmitter press its Up & Down buttons simultaneously until the motor jogs.
D. Before pressing the programming button on the transmitter, verify the motor directions (if DOWN on the transmitter corresponds to DOWN on
the end-product) and set (program) the end limits of the motor. Refer to section 4.3 of this instruction.
E. The motor is packaged in "FACTORY MODE", and will remain in this mode until the limits are set and the programming button on the
transmitter is pressed, thus putting it into "USER MODE". ROTATION DIRECTION CAN ONLY BE MODIFIED IN "FACTORY MODE".
F. A double power cut cannot be achieved if the motor is still in FACTORY or INSTALLER mode. First program a transmitter into the memory of
the motor.
G.
WARNING:
For the EOLIS/SOLIRIS RTS SENSOR to function properly, the transmitter which is memorized into the motor's receiver must be configured
correctly. The DOWN button MUST correspond to DOWN on the end-product. In the case of a cassette awning, it will open or extend the awning.
If the UP button extends the awning, the wind sensor will also extend the awning during windy conditions. THIS IS DANGEROUS! Damage and injury
could occur. Do not proceed until proper operation of the transmitter is verified.
H. The OREA RTS motor must be installed in the tube required for the particular application because the electronic speed variance detection will not allow the
motor to turn if the crown does not rotate.
120 VAC / 60 Hz
The Master Channel on a 4 channel transmitter can be used as an additional individual channel
for a total of 5 channels, without the option of master control of all motors
Range: Up to 65 feet from the motor
TELIS 1 RTS
TRANSMITTER
DECORA RTS 1
SWITCH
TELIS 4 RTS
TRANSMITTER
TELIS SOLIRIS RTS
TRANSMITTER
DECORA RTS 4
SWITCH
SOLIRIS SENSOR RTS
TELIS 1 RTS
1 CHANNEL
UP
STOP
DOWN
CHANNEL
INDICATOR
LED
CHANNEL
SELECTOR
4.7in/120mm
1.8in/45mm
TELIS 4 RTS
4 INDIVIDUAL CHANNELS
& 1 MASTER CHANNEL
BACK
PROGRAMMING
BUTTON
SIDE
0.7in
mm
/17
PROGRAMMING
BUTTON
SIDE
The Orea RTS is designed exclusively for cassette folding arm awnings
It features an integrated radio receiver with remote limit setting and remote user programmable intermediate stop.
The Orea RTS radio receiver (433.42 MHz) must be programmed with the Inteo family of transmitters.
The Orea RTS motors are compatible with SOLIRIS and EOLIS RTS Sensors.
MOTOR WIRING
COLOR CODE
120 VAC
CODE
BLACK
WHITE
GREEN
HOT
NEUTRAL
GROUND
A. All wiring must conform to NEC (National Electrical Code) and local codes.
B. The OREA RTS motors can be wired in PARALLEL.
A means of disconnecting the power at each motor independently should
be provided.
C. Power only needs to be supplied to the motor. The receiver is completely
enclosed inside the motor tube.
D. The external antenna will be phased out and become internal to the motor.
E. SOMFY Reserves the right to void the motor warranty if wiring
recommendations are not followed.
120
V
A
C
60
Hz
NEUTRAL
GROUND
GREEN
WHITE
HOT
BL
ACK
ANTENNA
Programming and Limit Setting Instructions
EOLIS SENSOR RTS
PROGRAMMING
BUTTON
-
+
-
+
Important Installation Tips
OREA RTS MOTOR