Yanmar 4TNV98 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 246

background image

4TNV98 & 4TNE98 Diesel Engine

Section 2. Periodic Maintenance

36

CAUTION

COOLANT HAZARD!

Wear eye protection and rubber gloves when
you handle long life or extended life engine
coolant. If contact with the eyes or skin should
occur, flush eyes and wash immediately with
clean water.
Failure to comply may result in minor or
moderate injury.

CAUTION

FLYING OBJECT HAZARD!

ALWAYS wear eye protection when servicing
the engine and when using compressed air or
high-pressure water. Dust, flying debris,
compressed air, pressurized water or steam
may injure your eyes.
Failure to comply may result in minor or
moderate injury.

CAUTION

Only use diesel fuels recommended by Yanmar
for the best engine performance, to prevent
engine damage and to comply with EPA/ARB
warranty requirements.
Only use clean diesel fuel.
NEVER remove the primary strainer (if
equipped) from the fuel tank filler port. If
removed, dirt and debris could get into the fuel
system causing it to clog.

CAUTION

Only use the engine oil specified. Other engine
oils may affect warranty coverage, cause
internal engine components to seize and / or
shorten engine life.
Prevent dirt and debris from contaminating the
engine oil. Carefully clean the oil cap/dipstick
and the surrounding area before you remove
the cap.
NEVER mix different types of engine oil. This
may adversely affect the lubricating properties
of the engine oil.
NEVER overfill. Overfilling may result in white
exhaust smoke, engine overspeed or internal
damage.

CAUTION

Only use the engine coolant specified. Other
engine coolants may affect warranty coverage,
cause an internal buildup of rust and scale
and/or shorten engine life.
Prevent dirt and debris from contaminating the
engine coolant. Carefully clean the radiator cap
and the surrounding area before you remove
the cap.
NEVER mix different types of engine coolants.
This may adversely affect the properties of the
engine coolant.

CAUTION

NEVER attempt to modify the engine’s design
or safety features such as defeating the engine
speed limit control or the diesel fuel injection
quantity control.
Modifications may impair the engine’s safety
and performance characteristics and shorten
the engine’s life. Any alterations to this engine
may void its warranty. Be sure to use Yanmar
genuine replacement parts.

«
...
36
37
38
39
40
...
»

Содержание 4TNV98























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 4TNV98

Бренд: Selve Страницы: 132

Бренд: Key Automation Страницы: 44

Бренд: Orion Страницы: 4

Бренд: Briggs & Stratton Страницы: 60

Бренд: Volvo Penta Страницы: 122

Бренд: Louvolite Страницы: 2

Бренд: O.S. engine Страницы: 4

BREVINI V Series

Бренд: DANA Страницы: 34

Бренд: Motion Страницы: 88

Бренд: Golden Eagle Страницы: 11

ANORAD LZ Series

Бренд: Rockwell Automation Страницы: 64

Бренд: LinMot Страницы: 24

Бренд: LinMot Страницы: 30

Бренд: Xtreme Power Страницы: 42

MICROMOTOR INTRA 32 MM-C SPRAY TB

Бренд: Dabi Atlante Страницы: 20

Бренд: KTM Страницы: 28

Бренд: Seidel Страницы: 17

EMF SQML160 Series

Бренд: EMF Motor Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды