Yanmar 4TNV98 Скачать руководство пользователя

Страница: 201 / 246

4TNV98 & 4TNE98 Diesel Engine

Section 4. Fuel System

199

Judgement Criteria on Atomization Condition

A B C D E

Injection
Pattern

Pressure
Gauge
Reading

Pointer fluctuate
around the valve
opening
pressure.

Same as A.

Pointer stays at
a position near
the valve
opening
pressure.

Although the
pointer reaches
the valve
opening
pressure, the
pressure drop is
large.

Pressure does
not increase
even when the
tester lever is

Atomization
Pattern

Roughly uniform. Atomization is

excessively one
sided.

Although
atomized, the
needle does not
pulsate (burner
like shape).

Bar shape with
excessive after
drops.

Drops (bar
shape).

Possible
Cause

(Normal)

Normally

caused by
carbon
contamination
of the nozzle
tip.

Sometimes

caused by
flaws in or
damage to the
needle tip.

Caused by

excessive
carbon
contamination
of the nozzle
tip.

Sometimes

caused by
contamination
.

Damage to

the seat.

Contamination

of seat by fine
foreign
particles.

Excessively

worn seat.

Sticking of

needle.

Excessively

damaged or
worn seat.

Contamination

of seat by
foreign matter.

Damaged or

broken
internal parts
od nozzle
holder.

Содержание 4TNV98























































































































































































































































Результаты поиска

Содержание 4TNV98

Отзывы:

Похожие инструкции для 4TNV98

Бренды по названию

Популярные бренды

Yanmar 4TNV98, Руководство по обслуживанию

Результаты поиска

Содержание 4TNV98

Отзывы:

Похожие инструкции для 4TNV98

Бренды по названию

Популярные бренды