Yanmar 4TNV98 Скачать руководство пользователя | Manualshive

Страница: 155 / 246

background image

4TNV98 & 4TNE98 Diesel Engine

Section 4. Fuel System

153

To locate the timing index number for the engine
being serviced use the Timing Index Chart under
“FIE Specs” on the Yanmar Distributor Website
(

http://distributor.yanmar.co.jp

).

If additional assistance is needed in locating the
engine timing index number See To Locate an
Authorized Yanmar Industrial Engine Dealer or
Distributor: Follow the instructions to locate an
authorized Yanmar industrial engine dealer or
distributor for assistance.

NOTE:

Treat the timing index number as if it has a

decimal point (68 = 6.8).

Figure 7-19

1.

Align the pump drive gear with the idler gear

using the reference marks made earlier.
4TNV98 model engines

(Figure 7-21, (1))

.

Figure 7-21

2.

If installing the fuel injection pump on an engine

with the front gear case cover removed, the fuel
injection pump drive gear can be aligned with the
idler gear by aligning the stamped marks

(A, B,

C)

on the fuel injection pump drive gear, idler

gear, and crankshaft drive gear. Ensure all three
timing marks

(Figure 7-22, (A, B, C)) are

aligned

.

Figure 7-22

(1) Fuel Injection Pump Drive Gear. (2) Camshaft Drive Gear.
(3) Auxiliary Drive Gear (Optional). (4) Crankshaft Drive Gear.
(5) Direction of Rotation. (6) Oil Pump Drive Gear (4TNV94L -
4TNV106). (7) Idler Gear

3.

Install a new O-ring on the pump mounting flange.

Apply grease to the O-ring to hold it in place
during installation of the injection pump.

NOTE:

Ensure the tapered surface of the fuel

injection pump shaft is clean and dry.

«
...
153
154
155
156
157
...
»

Содержание 4TNV98























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 4TNV98

Бренд: Wartsila Страницы: 168

Бренд: V2 Страницы: 14

MWM INTERNATIONAL MaxxForce 9.3P

Бренд: Navistar Страницы: 126

Бренд: Man Страницы: 136

Бренд: Flux Страницы: 20

Бренд: Turnigy Страницы: 2

Бренд: Danfoss Страницы: 77

Бренд: DELTA DORE Страницы: 16

Бренд: Toyama Страницы: 44

Бренд: DLE Страницы: 4

Бренд: Baldor Страницы: 1

Бренд: Yanmar Страницы: 14

Бренд: Yanmar Страницы: 52

Бренд: Yanmar Страницы: 66

Бренд: Yanmar Страницы: 264

Бренд: Yanmar Страницы: 350

Бренд: Toyota Страницы: 525

Бренд: Nanomotion Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды